8
8
8-103
8-103
Service Mode > COPIER > FUNCTION > DBG-LOG
Service Mode > COPIER > FUNCTION > DBG-LOG
■
DBG-LOG
COPIER > FUNCTION > DBG-LOG
LOG2USB
Storage of debug log to USB memory
Lv.1 Details
To store a set of debug logs to USB memory at the error occurrence.
A type of log to be collected is set in LOG-TRIG.
If there is a debug log which is automatically stored, it is archived at
this time.
Required time differs according to the device conditions and volume of
log data.
Use case
When analyzing the cause of a problem
Adj/set/operate method 1) Install the USB memory.
2) Select the item, and then press OK key.
Caution
- Wait until the machine recognizes the USB memory (approx.10 sec.).
- During the data transfer (“ACTIVE” display), do not turn OFF the
power/remove the USB memory/use the screen for operations.
Display/adj/set range
During operation: ACTIVE, At normal termination: OK!, At abnormal
termination: NG
Required time
Approx. 5 minutes
Related service mode COPIER> FUNCTION> DBG-LOG> LOG-TRIG
LOG2SRVR
Transfer of debug log to server
Lv.1 Details
To transfer a set of debug logs to FTP server using network at the
error occurrence.
A type of log to be collected is set in LOG-TRIG.
If there is a debug log which is automatically stored, it is archived at
this time.
Address and account of the FTP server can be set by reading the
operation setting file from the USB memory in LOG-TRIG.
Use case
When analyzing the cause of a problem
Adj/set/operate method Select the item, and then press OK key.
Caution
- Be sure to set the account of the machine to the FTP server
beforehand.
- During the data transfer (“ACTIVE” display), do not turn OFF the
power/use the screen for operations.
Display/adj/set range
During operation: ACTIVE, At normal termination: OK!, At abnormal
termination: NG
Related service mode COPIER> FUNCTION> DBG-LOG> LOG-TRIG
COPIER > FUNCTION > DBG-LOG
LOG-TRIG
Set of debug log storage condition
Lv.1 Details
To set the conditions (timing, types, etc.) to automatically store the
debug logs (stored as an archive file).
By reading the operation setting file of the setting value from the Main
Controller, the conditions written in the file are set.
When setting a new condition is necessary, read the operation setting
file provided by R&D from the USB memory.
Use case
- When changing the conditions of debug log to automatically store
- When setting a new condition
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
0 to 99999
101:Exc E-code + reboot
111:Exception only
121:E-code only
131:Reboot only
201:101 + alarm
211:Exc alarm
221:E-code + alarm
231: alarm
291:Alarm only
301:101 + jam
311:Exc jam
321:E-code + jam
331: jam
391:Jam only
Default value
101
Related service mode COPIER> FUNCTION> DBG-LOG> LOG2USB, LOG2SRVR
HIT-STS
Display of debug log state
Lv.1 Details
To display whether archive file of the debug log which was matched
with the conditions set in LOG-TRIG exists or not.
Use case
When checking the debug log automatically stored
Adj/set/operate method Select the item, and then press OK key.
Display/adj/set range
At normal state: OK, At failure occurrence: --
Related service mode COPIER> FUNCTION> DBG-LOG> LOG-TRIG
SYSLOG
Setting of syslog function
Lv.1 Details
To set the syslog function.
When ON is set, sublog on the main CPU side of the Main Controller
is output to the HDD/syslog server.
“sublog” can be collected by LOG2USB or LOG2SRVR.
Use case
When R&D considers that setting the syslog function is necessary at
problem analysis
Adj/set/operate method Enter the setting value, and then press OK key.
Caution
Do not use this at the normal service.
Display/adj/set range
0 to 99999
0: OFF
Default value
0
Related service mode COPIER> FUNCTION> DBG-LOG> LOG2USB, LOG2SRVR
