6
6
6-23
6-23
Troubleshooting > Troubleshooting Items > Operation failure > JAM ”0d91”during the PG print
Troubleshooting > Troubleshooting Items > Operation failure > JAM ”0d91”during the PG print
C: Varies according to the EXT-TBOX value
Service mode
setting value
Display timing of Waste Toner Container preparation warning
"0"
Below (1) or (2), whichever is earlier after the Waste Toner Full Sensor is ON.
(1) Count of the number of sheets: 5000 (1-sided: 1, 2-sided: 2, small size: 1, large
size: 2)
(2) Developing supply count: Supply amount equivalent to approx. 5000 counts at
5% image ratio
* This number of sheets decreases as the image ratio increases.
"1"
Below (1) or (2), whichever is earlier after the Waste Toner Full Sensor is ON.
(1) Count of the number of sheets: 6000 (1-sided: 1, 2-sided: 2, small size: 1, large
size: 2)
(2) Developing supply count: Supply amount equivalent to approx. 6000 counts at
5% image ratio
* This number of sheets decreases as the image ratio increases.
- - -
- - - -
"4"(Default
setting)
Below (1) or (2), whichever is earlier after the Waste Toner Full Sensor is ON.
(1) Count of the number of sheets: 9000 (1-sided: 1, 2-sided: 2, small size: 1, large
size: 2)
(2) Developing supply count: Supply amount equivalent to approx. 9000 counts at
5% image ratio
* This number of sheets decreases as the image ratio increases.
- - -
- - - -
"9"
Below (1) or (2), whichever is earlier after the Waste Toner Full Sensor is ON.
(1) Count of the number of sheets: 14000 (1-sided: 1, 2-sided: 2, small size: 1,
large size: 2)
(2) Developing supply count: Supply amount equivalent to approx. 14000 counts at
5% image ratio
* This number of sheets decreases as the image ratio increases.
By using this service mode, the Waste Toner Container can be used effectively, but waste
toner may overflow depending on the environment or status of usage. Therefore, the value
must be set carefully. Following shows the reference for setting.
CAUTION:
Even setting the service mode as above, waste toner leak may occur depending
on usage of the user. (If a user prints a large volume of solid images in color, it may
overflows.)Therefore, when changing the value, be sure to check the status of usage to
confirm that not so many solid images in color have been output, and do not set a large
value at once.
For the user who output a large volume of solid images in color, do not use this service
mode.In summer, volume of waste toner tends to increase. Be careful not to increase
the value too much before summer.
T-6-15
■
Alignment error in Inner Finisher
[Location]
Delivery Outlet of Inner Finisher
[Cause]
Alignment error due to occurrence of unexpected curl.
[Condition]
Because it occurs unexpectedly, it may occur in all environments although the possibility is
low. In a high temperature and humidity environment, the problem is likely to occur.
[Field Remedy]
Execute the following service mode for fixing temperature control. Recommended setting
value is -2. If the value is decreased too much, a fixing failure may occur; thus, be careful
when using this mode.
COPIER > OPTION > CUSTOM > TMP-TBL <Level1>
■
JAM ”0d91”during the PG print
[Location]
Multi-purpose Tray
[Cause]
The Multi-purpose Tray paper setting is not appropriate.
[Condition]
When the service mode “COPIER>TEST>PG>PG-PICK “ is set to 6(Multi-purpose Tray) and
the paper size selection is incorrect.
[Remedy]
After removing the jam papers, turn OFF and ON the main power SW.
In case of re-printing the PG print, set the paper size to a correct size or set the service mode
“COPIER>TEST>PG>PG-PICK” to any value other than 6.
