YASKAWA HV600, Руководство пользователя

Страница: 71 / 610

Parameter
List
1
1.10 H: Terminal Functions
YASKAWA TOEPYAIHV6002A HV600 Drive Programming 71
Setting Value Function Description Ref.
5 Accel/Decel Time Gain
Enters a signal to adjust the gain used for C1-01 to C1-04 [Acceleration/Deceleration Times 1 and 2] and C1-09 [Fast
Stop Time] when the full scale analog signal (10 V or 20 mA) is 100%.
330
6 DC Injection Braking
Current
Enters a signal to adjust the current level used for DC Injection Braking when the drive rated output current is 100%.
331
7 Torque Detection Level
Enters a signal to adjust the overtorque/undertorque detection level.
Note:
Use this function with L6-01 [Torque Detection Selection 1] . This parameter functions as an alternative to L6-02
[Torque Detection Level 1] .
331
8 Stall Prevent Level
During Run
Enters a signal to adjust the stall prevention level during run if the drive rated current is 100%.
331
9 Output Frequency Lower
Limit
Enters a signal to adjust the output frequency lower limit level as a percentage of the maximum output frequency.
Note:
Parameter A1-02 [Control Method Selection] selects which parameter is the maximum output frequency.
•
A1-02 ≠ 8 [EZOLV] : E1-04 [Maximum Output Frequency]
•
A1-02 = 8 : E9-02 [Maximum Speed]
332
B PID Feedback
Enter the PID feedback value as a percentage of the maximum output frequency.
Note:
Parameter A1-02 [Control Method Selection] selects which parameter is the maximum output frequency.
•
A1-02 ≠ 8 [EZOLV] : E1-04 [Maximum Output Frequency]
•
A1-02 = 8 : E9-02 [Maximum Speed]
332
C PID Setpoint
Enters the PID setpoint as a percentage of the maximum output frequency.
Note:
Parameter A1-02 [Control Method Selection] selects which parameter is the maximum output frequency.
• A1-02 ≠ 8 [EZOLV] : E1-04 [Maximum Output Frequency]
• A1-02 = 8 : E9-02 [Maximum Speed]
332
D Frequency Bias
Enters the bias value added to the frequency reference as a percentage of the maximum output frequency.
Note:
Parameter A1-02 [Control Method Selection] selects which parameter is the maximum output frequency.
• A1-02 ≠ 8 [EZOLV] : E1-04 [Maximum Output Frequency]
• A1-02 = 8 : E9-02 [Maximum Speed]
332
E Motor Temperature (PTC
Input)
Uses the motor Positive Temperature Coefficient (PTC) thermistor to prevent heat damage to the motor as a percentage
of the current value when the 10 V analog signal is input.
332
F Not Used
Use this setting for unused terminals or to use terminals in through mode.
333
10 Forward Torque Limit
Enters the forward torque limit when the motor rated torque is 100%.
333
11 Reverse Torque Limit
Enters the load torque limit if the motor rated torque is 100%.
334
12 Regenerative Torque
Limit
Enters the regenerative torque limit if the motor rated torque is 100%.
334
15 General Torque Limit
Enters the torque limit that is the same for all quadrants for forward, reverse, and regenerative operation if the motor
rated torque is 100%.
334
16 Differential PID
Feedback
Enters the PID differential feedback value if the full scale analog signal (10 V or 20 mA) is 100%.
334
1F Not Used
Use this setting for unused terminals or to use terminals in through mode.
334
24 PID Feedback Backup
Enters the PID Feedback Backup signal for the drive to use when it loses the primary PID feedback set for H3-xx = B
[PID Feedback] .
Note:
The full-scale of the analog signal goes from b5-71 [Min PID Transducer Scaling] to b5-38 [PID User Unit
Display Scaling] .
335
V/f OLV/PM OLV/PM EZOLV
V/f OLV/PM OLV/PM EZOLV
V/f OLV/PM OLV/PM EZOLV
V/f OLV/PM OLV/PM EZOLV
V/f OLV/PM OLV/PM EZOLV
V/f OLV/PM OLV/PM EZOLV
V/f OLV/PM OLV/PM EZOLV
V/f OLV/PM OLV/PM EZOLV
V/f OLV/PM OLV/PM EZOLV
V/f OLV/PM OLV/PM EZOLV
V/f OLV/PM OLV/PM EZOLV
V/f OLV/PM OLV/PM EZOLV
V/f OLV/PM OLV/PM EZOLV
V/f OLV/PM OLV/PM EZOLV
V/f OLV/PM OLV/PM EZOLV
V/f OLV/PM OLV/PM EZOLV
V/f OLV/PM OLV/PM EZOLV