ISD94100 Series Technical Reference Manual
Sep 9, 2019
Page
695
of 928
Rev1.09
IS
D
9
410
0
S
ER
IE
S
T
E
C
HN
ICA
L
RE
F
E
RE
NCE
M
AN
U
AL
RXEMPTY = 1
RXEMPTY = 1
RXEMPTY = 1
b31|b30...b1|b0
b0
Data 0
RXEMPTY = 0
Example 1
SPI0
DWIDTH =0
LSB = 1
RX Skew Buffer
RX Shift Register
RX FIFO Buffer
H/W Load
Skew Buffer
into Shift
Register
b1
……………
.b0
b32
…………
..b32
b33
1. H/W load Shift
Register into RX
FIFO
2. H/W Load
Skew Buffer into
Shift Register
RXEMPTY = 1
RXEMPTY = 0
RXEMPTY = 0
RXFULL = 1
Example 2
SPI0
DWIDTH =0
LSB = 1
Data 1
Data N
b31|b30...b1|b0
Data 0
1. H/W load
Shift Register
into RX FIFO
2. H/W Load
Skew Buffer
into Shift
Register
Data 9
1. Read Out by
User
2. Repeat
Receive Data
into RX FIFO
Data 1
Data 2
Data 3
Data 4
Data 5
Data 6
Data 7
Data 8
RXEMPTY = 0
RXFULL = 1
RXOVIF = 1
Data 1
Data 2
Data 3
Data 4
Data 5
Data 6
Data 7
Data 8
RX Shift Register
RX FIFO Buffer
H/W Load 32
bits into
Shift Register
The 9
th
Data
can not load
into RX FIFO
Buffer when
RX FIFO Full
Figure 6.14-24 Receive FIFO Buffer Example
In Slave mode, during transmission operation, when data is written to the SPIn_TX register by
software, the data will be loaded into transmit FIFO buffer and the TXEMPTY (SPIn_STATUS[16])
will be set to 0. The transmission will start when the slave device receives clock signal from master.
Data can be written to SPIn_TX register as long as the TXFULL (SPIn_STATUS[17]) is 0. After all
data have been drawn out by the SPI transmission logic unit and the SPIn_TX register is not
updated by software, the TXEMPTY (SPIn_STATUS[16]) will be set to 1.
If there is no any data written to the SPIn_TX register, the transmit underflow interrupt flag, TXUFIF
(SPIn_STATUS[19]) will be set to 1 when the slave selection signal is active. The output data will
be held by TXUFPOL (SPIn_FIFOCTL[6]) setting during this transfer until the slave selection signal
goes to inactive state. When the transmit underflow event occurs, the slave under run interrupt flag,
SLVURIF (SPIn_STATUS[7]), will be set to 1 as slave selection pin goes to inactive state.
SPIx_SSy pin
SPIx_CLK pin
SPIx_MISOz pin
TXEMPTY
SLVURIF
TXUFPOL
TXUFIF
Data 0 is written
into FIFO Buffer
Data 0
Read & Clear by
User
Note:
x: Controller number (x = 0, 1, 2), y: Slave selection pin channel number in SPI0 (y = 0, 1),
z: MOSI and MISO pin channel number in SPI0 (z = 0)
Содержание ISD94100 Series
Страница 528: ...ISD94100 Series Technical Reference Manual Sep 9 2019 Page 528 of 928 Rev1 09 ISD94100 SERIES TECHNICAL REFERENCE MANUAL...
Страница 626: ...ISD94100 Series Technical Reference Manual Sep 9 2019 Page 626 of 928 Rev1 09 ISD94100 SERIES TECHNICAL REFERENCE MANUAL...
Страница 702: ...ISD94100 Series Technical Reference Manual Sep 9 2019 Page 702 of 928 Rev1 09 ISD94100 SERIES TECHNICAL REFERENCE MANUAL...
Страница 875: ...ISD94100 Series Technical Reference Manual Sep 9 2019 Page 875 of 928 Rev1 09 ISD94100 SERIES TECHNICAL REFERENCE MANUAL...