Mindray Passport V Скачать руководство пользователя страница 243

Страница: 243 / 288

Performance Characteristics

Appendix

19 - 8

0070- 0-0704-02

Passport V Operating Instructions

Common Mode Rejection Ratio

• Monitor mode: >105 dB measured at 50 and 60 Hz

• Surgical mode: >105 dB measured at 50 and 60 Hz

• ST mode: > 105 dB measured at 50 and 60 Hz

• Diagnostic mode: >90 dB measured at 50 and 60 Hz

Notch Filter

• Notch filter settable to 50 Hz or 60 Hz

Input Bias Current

•

≤

0.1 µA .

• Complies with 4.2.5 of ANSI/AAMI EC13:2002.

Electrode Offset Potential Tolerance

• +/- 500 mV

• Complies with 4.2.9.1 of ANSI/AAMI EC13:2002

RTI Noise

•

≤

30 µV (p-v RTI)

• Complies with 4.2.9.3 of ANSI/AAMI EC13:2002.

ESU (Electrosurgical Unit) Interference Suppression

• Incision mode: 300W

• Coagulation mode: 100W

• Recovery time :

≤

10s

• Complies with 4.2.9.14 of ANSI/AAMI EC13:2002.

RTI Suppression of ESU (Electrosurgical Unit)

• ESIS ECG cable is used.

• ECG lead wires complying with AAMI is used; compared with ECG baseline, the peak-to-

peak RTI value:

≤

2mV.

• The testing method complies with 5.2.9.14 of EC13:2002.

ESU Filter Control

• Auto / Off indications:

• Auto: ESU detection shall engage the surgical mode filter if the ESU detection

measures ESU pulses at a rate > 50 Hz or > 50 spikes per second. ESU detection shall
stop the surgical mode filter if the ESU detection measures ESU pulses at a rate < 10
Hz or < 10 spikes per second.

• Off: ESU filter is off.

Содержание Passport V

































































































































































































































































































Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды

Mindray Passport V, Руководство по эксплуатации

Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды