Mindray Passport V Скачать руководство пользователя страница 15

Страница: 15 / 288

Introduction

Precautions

xii

0070- 0-0704-02

Passport V Operating Instructions

WARNING: CO

FilterLines

should be treated as biohazardous waste and

disposed of in accordance with local regulations for

contaminated and biologically hazardous items.

WARNING: Use the recommended cleaning methods for the DRYLINE

™

water traps. Do not clean or wash the filter housing of the
water trap. Never allow alcohol to enter the filter housing.

Never force air through the water trap.

WARNING: A hazard can exist if different alarm presets are used for the

same or similar equipment in any single area.

WARNING: The user should check that the current alarm settings on the

Passport V monitor are appropriate prior to use on each

patient.

Precautions

CAUTION:

Always place the monitor on a rigid, flat surface or on

approved mounts. Do not block ventilation or speaker vents.

CAUTION:

Do not carry the Passport V using the integrated grip handle if

the unit is mounted to another item (e.g., a rolling stand or Gas
Module 3).

CAUTION:

Never place fluids on top of this monitor. In case of accidental
spillage, wipe clean immediately and have the monitor serviced

to ensure no hazard exists.

CAUTION:

To avoid possible damage to the Passport V, and to provide

protection against the effect of the discharge of a cardiac

defibrillator and against burns, use only approved ECG cables
and approved accessories listed in the Accessories chapter.

CAUTION:

To prevent condensation, allow the Passport V to warm up and
dry if it is moved from a cold to warm location.

CAUTION:

The Passport V may not meet its performance specifications if
stored or operated outside of specified temperature and

humidity ranges.

CAUTION:

Prior to use, be sure the rail supporting the bed rail mounting

hook can support the weight of the monitor. Consult the bed

manufacturer’s specifications if necessary. The Company is not
responsible for injury or damage resulting from improper or

inadequate support of the monitor.

CAUTION:

Use the power cord provided with the product. If a substitute is

necessary, use only hospital grade power cords.

Содержание Passport V

































































































































































































































































































Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды

Mindray Passport V, Руководство по эксплуатации

Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды