Mindray Passport V Скачать руководство пользователя страница 194 | Manualshive

Страница: 194 / 288

background image

Passport V Operating Instructions

0070- 0-0704-02

14 - 17

Messages

Prompt Messages

GM: O

2

Zero Error

Appears when the system has
been unable to successfully zero
the O

2

sensor.

Manually start zeroing the
system again. If problem
persists, contact Mindray
Technical Support.

GM: Cannot Zero...Retrying

Appears when the

Passport V

requests

Zeroing

(either on the

automatic cycle or by a user
request) and the Gas Module is
unable to initialize the cycle.

Allow system to retry without
intervention. If problem persist,
contact Mindray Technical
Support

GM: Zero In Progress

Appears when the system is
zeroing all of its channels. This
appears whether initiated by the
user or is automatic.

This is normal operation.
Wait for message to clear.

GM: Warming Up

Appears when the system has
been turned on, and the sensors
have not reached their stable
operating temperature.

Wait for the message to go
away. It takes up to five
minutes for the device to warm
up.

GM: Air Leak

Appears when the system detects
a pneumatic leak.

Also may appear when the Gas
Module has been turned on
without a sample line attached.

Gas Module has been on for a
long period of time without the

Passport V

monitor being on.

Turn Gas Module and

Passport V

Off.

Install/check sample lines,
filters, water trap and electrical
connections.

Turn off Gas Module.Turn on
Gas Module and

Passport V

monitor

GM: Replace Trap

Indicates residue build-up on the
water trap membrane that is
decreasing air flow.

Replace water trap reservoir.

GM: Exhaust Blocked

Appears when the system detects
a blockage at the exhaust gas
outlet, as indicated by an
increase in internal pressure.

Remove waste gas
scavenging assembly, check if
message disappears.
Check exhaust line for
blockage and clear if possible.
If message persists contact
Mindray Technical Support.

GM: Failed

Appears when the Gas Module
detects an unrecoverable error in
its own operation.

Contact Mindray Technical
Support.

GM: Occlusion

Appears when the system detects
an obstruction in the sampling
line or the water trap bottle is
full.

Empty and rinse water trap.
Change water trap if
necessary. Check sampling line
and filter for blockage,
clear sampling line if possible.
Replace sampling line and/or
filter if necessary.
Check exhaust line for
blockage and clear if possible.
If problem persists, contact
Mindray Technical Support.

GM: Pump Off

Appears when the system has
turned off the pump due to a
pneumatic error.

Restart the pump from the

Gas

Menu

. If problem persists,

contact Mindray Technical
Support.

«
...
192
193
194
195
196
...
»

Содержание Passport V

































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Passport V

Бренд: Source Страницы: 31

Universal Roof HKA11-12074

Бренд: Petsafe Страницы: 24

Бренд: U-Line Страницы: 6

Front Wheel Attachment

Бренд: Walkin’ Pets Страницы: 4

Sealed Pet Bowl

Бренд: SureFeed Страницы: 86

Spelos Xl Metro

Бренд: Savic Страницы: 4

Xeno2 500.521.00.1

Бренд: Geberit Страницы: 64

Outdoor Shields Avoidance System

Бренд: INVISIBLE FENCE Страницы: 12

POWER KNEE PKA01

Бренд: Össur Страницы: 15

Бренд: Deuba Страницы: 8

Бренд: Petsafe Страницы: 8

Бренд: Bobrick Страницы: 2

Бренд: Hamilton Страницы: 4

Satin Skin HL 36

Бренд: Beurer Страницы: 98

HOBBY Hygro-Plus

Бренд: DOHSE AQUARISTIK Страницы: 2

Бренд: Healthport Страницы: 2

Бренд: Okoia Страницы: 62

Бренд: Nora Bode Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды