manualshive.com logo in svg

Mindray Passport V, Руководство по эксплуатации

Познакомьтесь с Mindray Passport V - передовым медицинским устройством для мониторинга пациентов. Для получения сервисного руководства бесплатно, загрузите его с нашего веб-сайта. Ознакомьтесь с подробной информацией о продукте и его функциях, чтобы узнать, как использовать его на максимуме.

Поделиться
Скачать
background image

NIBP Description

NIBP Monitoring

7 - 2

0070- 0-0704-02

Passport V Operating Instructions

7.1.3

Measurement Modes   

The 

Passport V 

Provides three measurement modes: Manual, Automatic, STAT modes.

Manual mode: 

When NIBP Interval is set to off, then the NIBP is in manual mode and  

"Off" appears in the NIBP numeric tile, the message  "NIBP: Manual Mode" is displayed in 
message area B.

Press START key to start an NIBP measurement. The message "NIBP: Measuring" is 
displayed. When the measurement is completed, the measured results are displayed and the 
monitor enters the NIBP waiting status and prompt message "NIBP: Idle" is displayed.

During the manual measurement, pressing the STOP key on the front panel, stops the manual 
measurement and prompt message "NIBP: Idle" is displayed until START is pressed again.

Automatic Mode: 

When NIBP Interval is set to anything other than Off, the NIBP is in 

automatic mode. Once the Automatic mode interval is selected, the prompt message "NIBP: 
Press the START key" is given in message area B.

Press START key to start the first NIBP measurement and prompt "NIBP: Measuring". When 
this time measurement is completed, the measured results are displayed and the prompt 
message "NIBP: Interval" is displayed. The next measurement will start after the selected 
interval has expired.

If the automatic interval is set at 1 minute, then after 10 minutes of automatic measurements 
the interval will change to a 10 minute interval. 

During the automatic measurement, pressing the STOP key on the front panel, will stop the 
automatic measurement. The message "NIBP: Idle" will be displayed until START is pressed 
again.

NOTE:

If the interval is changed during the Automatic 
measurement interval, the new interval starts from the time 
when such change is made.

NOTE:

In Automatic Mode, a measurement can be started 
manually during the interval between two timed 
measurements. If STOP key is pressed, both the manual 
mode measurement and automatic mode measurement  are 
stopped.

NOTE:

When the system time is changed during the automatic 
measurement, it will enter idle mode after completing the 
current measurement. Press the START key on the front 
panel if it is necessary to start measurement. 

STAT Mode: 

When NIBP Interval is set to STAT mode, "STAT" appears in the NIBP numeric 

tile and the prompt message  "NIBP: STAT" is displayed in message area B.

Press the START key to start the STAT measurement sequence and the message "NIBP: 
Measuring" appears in message area B. When this measurement is completed, the results 
are displayed. STAT measurements will continue for a period of 5 minutes. Afterward, the 
monitor will switch to 5-minute intervals.

During the STAT measurement, press STOP key on the front panel, stop the STAT measurement 
and the prompt message "NIBP: Idle" will be displayed until START is pressed again.

NOTE:

If the 5 minute STAT cycle expires and a measurement is in 
progress, the STAT cycle will end at completion of the 
measurement that is in progress.

0

Содержание Passport V

































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Passport V

Sunbeam HEALTHATHOME 739 User Manual preview
HEALTHATHOME 739
Бренд: Sunbeam Страницы: 8
Petsafe PWM00-16580 Quick Start Manual preview
PWM00-16580
Бренд: Petsafe Страницы: 4
Elamed ALMAG-03 Operating Manual preview
ALMAG-03
Бренд: Elamed Страницы: 28
Orliman SITLIVE OSL1102 Instructions For Use And Preservation preview
SITLIVE OSL1102
Бренд: Orliman Страницы: 12
Laufen Leelo 4.4761.1 Manual preview
Leelo 4.4761.1
Бренд: Laufen Страницы: 6
Kagan Migraine Magic Plus Instruction Booklet preview
Migraine Magic Plus
Бренд: Kagan Страницы: 9
VRI MobileHelp Solo Instructions preview
MobileHelp Solo
Бренд: VRI Страницы: 2
CatLink One Pet AI Feeder User Manual preview
One Pet AI Feeder
Бренд: CatLink Страницы: 8
Hawx DG/Hunter Operating Manual preview
DG/Hunter
Бренд: Hawx Страницы: 35
Brookstone 324458 Manual preview
324458
Бренд: Brookstone Страницы: 2
Spectrum WatchDog 3665R Product Manual preview
WatchDog 3665R
Бренд: Spectrum Страницы: 4
DogWatch BigLeash S-15 Owner'S Manual preview
BigLeash S-15
Бренд: DogWatch Страницы: 28
Lanaform LA130507 Manual preview
LA130507
Бренд: Lanaform Страницы: 28
simplehuman TRIO MAX Instructions Manual preview
TRIO MAX
Бренд: simplehuman Страницы: 8
Tanita InnerScan BC-533 Instruction Manual preview
InnerScan BC-533
Бренд: Tanita Страницы: 23
pawpail PP1030 User Manual preview
PP1030
Бренд: pawpail Страницы: 4
PawHut D31-012 Assembly Instruction preview
D31-012
Бренд: PawHut Страницы: 3
PawHut D10-025V01 Assembly & Instruction Manual preview
D10-025V01
Бренд: PawHut Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды