Mindray Passport V Скачать руководство пользователя страница 264

Страница: 264 / 288

Passport V Operating Instructions

0070- 0-0704-02

19 - 29

Appendix

Communication Protocols

19.10

Communication Protocols

DIAP Communication Protocol

The

Passport V

supports the proprietary DIAP (0070-00-0307).

Gas Module

The

Passport V

supports the Gas Module Communication Protocol (0084-00-0025).

Alarm Delay Time to Remote Equipment

The alarm delay time from the

Passport V

to remote equipment is

≤

2 seconds, measured at

the

Passport V

signal output connector.

19.11

Data Storage

Monitor Configuration Data Storage and Transfer

Storage

The monitor has the ability to store, in non-volatile memory, the user-selectable configuration.
There is one (1) configuration available for each patient size and the following information is
saved:

• Alarm Values

• Display Configurations

• NIBP Interval

• Parameter Settings, Scaling

• Trace Speed

• Printer Settings

• Trend Configurations

Patient Data Storage and Transfer

Storage

The current patient information and demographics is stored in non-volatile memory.

Содержание Passport V

































































































































































































































































































Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды

Mindray Passport V, Руководство по эксплуатации

Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды