Mindray Passport V Скачать руководство пользователя страница 161

Страница: 161 / 288

Gas Module Troubleshooting

Gas Monitoring (optional)

11 - 8

0070- 0-0704-02

Passport V Operating Instructions

10.

If not already set, use the

Display Setup Menu

to select the gas waveforms to be

displayed.

11.

If desired, the gas waveform speed and scale can be changed in the

Gas Menu

11.3.3

Gas Module 3 Pre-use Test

Prior to each use, perform the following test with the Gas Module 3 to verify that the gas
analyzer and sample system are functioning properly:

Verify that the appropriate water trap is properly installed and that the appropriate
sampling line is connected.

• DRYLINE

™

Adult/Pediatric water trap used with DRYLINE

™

Adult/Pediatric sampling

line (colorless Luer lock nut)

• DRYLINE

™

Neonatal water trap used with DRYLINE

™

Neonatal sampling line (blue

Luer lock nut)

Verify that the water trap container is less than half full.

Occlude the sampling line and verify that the occlusion alarm functions properly.

Breathe into the sampling line and verify that a CO

waveform is correctly displayed on

the monitor.

Sample room air for 30 seconds and verify that the monitor oxygen output is 21%
(± sensor inaccuracy).

11.4

Gas Module Troubleshooting

Refer to Chapter 14.0

Messages for Physiological Alarm Messages, Technical Alarm

Messages, and Prompt Messages.

Содержание Passport V

































































































































































































































































































Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды

Mindray Passport V, Руководство по эксплуатации

Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды