Mindray Passport V Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 288

background image

Passport V Operating Instructions

0070- 0-0704-02

4 - 9

ECG Monitoring

Menus: ECG Main and Submenus

To display the Arrhythmia Menu:

1.

On the front panel, press the

Alarms: Limits

key to display the

Alarm Settings

Menu

, and select

Arrhythmia Menu

or
On the normal screen:
Select

Monitor Setup

〉

Advanced Setup

〉

Arrhythmia Menu

or
Select

Parameters

〉

ECG

〉

Arrhythmia Menu

or
Select the

ECG

tile

〉

Arrhythmia Menu

.

2.

To exit, press the

Normal Screen

key on the front panel.

Arrhythmia Menu

MENU ITEM

SELECTIONS

COMMENTS

Previous Menu

—

Select to return to previous menu.

Arrhythmia Setup

Asystole
V-Tach
V-Fib
PVC/min
V-Rhythm
Couplet
Run
Bigeminy
Trigeminy
Irregular HR
Brady

Select to set individual arrhythmia alarm
characteristics.

For each arrhythmia selection, choose:
Alarm: On or Off
Priority: 1 or 2
Print: On or Off

Lethal arrhythmias (Asystole, V-Tach, and V-Fib) are
Priority 1 and cannot be changed. The factory default
for all arrhythmia alarms is On.

All On

—

Select to set all arrhythmia alarms to On.

Non-lethals off

—

Select to set all non-lethal arrhythmia alarms to Off.

All Off

—

Select to set all arrhythmia alarms to Off.

“All Off” is displayed only if “Enable Arrhythmia All
Off Selection” = Yes in the

Installation Menu

.

Relearn

—

Select to manually initiate the relearning process for ST
Measurements or Arrhythmia Analysis.

Disabled if Arrhythmia = Off.

After relearning is started, arrhythmia relearning and
ST relearning are performed simultaneously. The
arrhythmia and ST analysis templates are recreated
and the message “Relearning...” is displayed. During
relearning, ST and PVCs are displayed as “– – –“.

Arrhythmia relearning should be started when:
• Lead type is changed.
• ECG lead wires are reconnected to the patient.
• Analysis lead is changed.
• Patient size is changed.
• Arrhythmia analysis is turned on.
• Module is turned on.
• Exiting Standby mode.

PVC/min

1 to 30
default = 10

Select to change the High PVC/min alarm rate limit.
The PVC/min parameter is displayed when PVC/min
arrhythmia alarm is set to On.

«
...
68
69
70
71
72
...
»

Содержание Passport V

































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Passport V

Icare HOME TA022

Бренд: Icare Страницы: 17

Бренд: Petsafe Страницы: 172

$Orliman 3-Tex Lumbo 6213 Instructions For Use And Preservation preview$

3-Tex Lumbo 6213

Бренд: Orliman Страницы: 12

Monoflex SH120L

Бренд: Bodypoint Страницы: 30

Бренд: Tru-Test Страницы: 28

ReFa RF-SW2323B

Бренд: MTG Страницы: 52

BLEND UP VIBRA-SONIC

Бренд: Magnitone Страницы: 16

Бренд: Oase Страницы: 19

Бренд: Clatronic Страницы: 74

Dog Auto Harness Fit & Tether

Бренд: BERGAN Страницы: 2

Бренд: Magnitone Страницы: 32

Бренд: mychway Страницы: 17

Бренд: Remington Страницы: 2

Бренд: aidapt Страницы: 8

Бренд: aidapt Страницы: 6

Smart Profile Uplift

Бренд: Clarisonic Страницы: 152

Бренд: HoMedics Страницы: 6

skin care brush

Бренд: Clarisonic Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды