Mindray Passport V Скачать руководство пользователя страница 198

Страница: 198 / 288

Passport V Operating Instructions

0070- 0-0704-02

14 - 21

Messages

Prompt Messages

14.3.14

ALARM MESSAGE

REASON

SOLUTION

Local Printer Comm Error

Contact Technical Support.

Local Printer SelfTest Error

Contact Technical Support.

Thermal Printhead
Overheated

Printer Initializing

Printer Searching...

Local Printer Busy

Printer received multiple print
requests at one time.

Wait until the printer is not
busy.

Local Printer Out Of Paper

Printer out of paper.

Replace with a new roll of
paper.

Local Printer Unable To Print

The system has detected an
unrecoverable printer failure.

Power cycle unit. If message
reappears, contact Mindray
Technical Support.

No printer selected or
available

No printer selected is available
from the network.

Check the selected printer from
the network and make sure the
printer model is supported by

Passport V

monitors.

Printing...

The printer is printing.

Printer Buffer Full

The printer buffer is full.

Local Printer Communication
Error

Local Printer communication is
interrupted.

Remote Printer Not Available

This message is displayed in the
case of a printer error.

Fix the printer.

Printing Complete

The printing is completed.

Содержание Passport V

































































































































































































































































































Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды

Mindray Passport V, Руководство по эксплуатации

Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды