Mindray Passport V Скачать руководство пользователя страница 204

Страница: 204 / 288

Passport V Operating Instructions

0070- 0-0704-02

15 - 5

Trends

Graphic Trends

15.4

Graphic Trends

The

Graphic Trend

display allows the user to view a graphic summary of stored patient

vital signs and anesthetic gas data. To access this display from the normal monitoring screen,
press the

TRENDS

key three times. To access this display from the

Quick Trend

display,

press the

TRENDS

key twice. To access this display from the

List Trend

display, press the

TRENDS

key once. This display may also be accessed from the other trend displays via a

menu choice.

FIGURE 15-3

Graphic Trends

The left side of the

Graphic Trend

display contains menu items for

scrolling, setup

and

access to other displays

. The

Graphic Trend

data window contains up to 5 parameter

displays. Use the vertical

Scroll

feature to view other parameters.

NOTE:

When scrolling vertically, the topmost parameter (HR)
remains displayed and does not scroll.

Time stamps are included in the upper area of the window, with the most recent data
appearing with the cursor at the right end. Use the horizontal

Scroll

feature to move the

display window through time. Scroll bars along the right and bottom sides of the

Graphic

Trend

display indicate the position of viewed data in relation to the rest of the database.

The

Event

feature may be used to scroll quickly between clock adjusted events and data

transfer events (caused by alarm violations and

MARK EVENT

keypresses).

The

Zoom

feature may be used to adjust the amount of time shown in the trend window.

The top line of the

Graphic Trend

display contains markers which indicate if the entry was

triggered by an alarm violation or by pressing the

MARK EVENT

key. These markers are

red for priority 1 alarms, yellow for priority 2 alarms, and green if initiated by pressing the

MARK EVENT

key. Clock adjusted events and data transfer event will be marked as well.

Содержание Passport V

































































































































































































































































































Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды

Mindray Passport V, Руководство по эксплуатации

Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды