Mindray Passport V Скачать руководство пользователя страница 216 | Manualshive

Страница: 216 / 288

background image

Passport V Operating Instructions

0070- 0-0704-02

17 - 3

User Maintenance

Care and Cleaning of SpO

2

Sensors

17.3

Care and Cleaning of SpO

2

Sensors

NOTE:

Refer to the individual instruction sheets that are packaged
with each sensor.

• Check sensors and cables daily for signs of damage. Replace as required.

• Sensors should be cleaned before and after each new patient.

• Wipe the patient contact area using a soft cloth with mild soap and water solution or

isopropyl alcohol. Hydrogen peroxide can be used to remove dried blood.

• Allow the sensor to completely dry before using.

CAUTION:

When cleaning SpO2 sensors, do not use excessive amounts
of liquid. Wipe the sensor surface with a soft cloth,
dampened with cleaning solution. Do not attempt to
sterilize.

Cleaning and Re-use of a Nellcor

®

Sensor

Sensors may be reattached to the same patient if the emitter and detector windows are clear
and the adhesive still adheres to the skin. The adhesive can be partially rejuvenated by
wiping with an alcohol wipe and allowing the sensor to thoroughly air dry prior to
replacement on the patient.

Do not immerse any Oxisensor

®

, OxiMax

®

, Durasensor

®

, Oxiband

®

, or Duraform

®

oxygen

transducers, the Nellcor

®

RS-10 or Max-Fast

®

oxygen transducers, or any Nellcor

®

adhesive

in water or cleaning solution. Clean Durasensor

®

, Oxiband

®

, and Duraform

®

oxygen

transducers, and the Nellcor

®

RS-10 or Max-Fast

®

oxygen transducers by wiping with a

disinfectant such as a solution containing 70% alcohol. Do not sterilize by irradiation, steam,
or ethylene oxide. Use a new Oxiband

®

adhesive wrap or FORM-A adhesive bandage for

each patient. Do not re-sterilize Oxisensor

®

or OxiMax

®

oxygen transducers.

17.4

Care and Cleaning of Reusable Temperature Probes

NOTE:

Refer to the individual instruction sheets that are packaged
with each temperature probe for additional information.

• Check temperature probes and cables daily for signs of damage. Replace as required.

• Probes should be cleaned before and after each new patient.

• Wipe the patient contact area using a soft cloth with mild soap and water solution or

isopropyl alcohol.

• Allow the probe to completely dry before using.

«
...
214
215
216
217
218
...
»

Содержание Passport V

































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Passport V

Бренд: Cabelas Страницы: 36

Бренд: NuvoMed Страницы: 3

Бренд: VS Sassoon Страницы: 20

SOFY-PLANT gel GL-121

Бренд: Orliman Страницы: 11

Бренд: Laufen Страницы: 6

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 3

HeartStart OnSite

Бренд: Philips Страницы: 3

Бренд: Philips Страницы: 7

Бренд: Philips Страницы: 12

lifeline AutoAlert Help Button FD100

Бренд: Philips Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды