Mindray Passport V Скачать руководство пользователя страница 190

Страница: 190 / 288

Passport V Operating Instructions

0070- 0-0704-02

14 - 13

Messages

Prompt Messages

14.3.6

IBP Prompt Message

14.3.7

Prompt Message

ALARM MESSAGE

REASON

SOLUTION

<IBP Label>: Communication
Error

IBP communicatuon error, the
command can not be send
correctly.

Power cycle unit. If message
reappears, contact Technical
Support.

<IBP Label>: Communication
Stop

As the IBP module
communication stops, the data
packets sent by the IBP module
can not be received.

Power cycle unit. If message
reappears, contact Technical
Support.

Pulsatile Pressure. Cannot
Zero!

Input the pulsatile pressure, can
not zero IBP channel.

Input the static pressure, re-zero
IBP channel.

Pressure Overrange. Cannot
Zero!

The pressure is overange, can
not zero IBP channel.

Check the static pressure value,
re-zero IBP channel.

ALARM MESSAGE

REASON

SOLUTION

COMMENTS

: Calibration Required

Calibration required
after 4000 operating
hours

Recalibrate
miniMediCO2.
Contact Technical
Support.

Oridion

: Filterline Disconnected

Filterline
disconnected

Connect Filterline to
monitor

Oridion
microstream

: Gas Can Be Removed

gas can be

removed.

—

Oridion

: Purge

Sample line is
blocked or kinked

Wait several seconds.
The

Passport V

will

return to monitoring, or
display the message:
“CO

: Occlusion”. If

message is displayed:
Check sample line.
Clear blockage or kink
or replace with a new
sample line.

Oridion
microstream

: Occlusion

Sample line is
blocked or kinked

Check sample line.
Clear blockage or kink
or replace with a new
sample line.

Oridion
microstream

: Sensor High

Temperature

Temperature
overranges high limit
checked by module.

Check,stop using or
replace the sensor.

DPM

: Sensor Low

Temperature

Temperature
overranges low limit
checked by module.

Check,stop using or
replace the sensor.

DPM

: High Airway Press.

Measurement of Flux
Sensor in module is
higer than 790
mmHg.

Check airway's output
and connection.
If problems remain
exist, return it to
factory for
maintaining.

DPM

Содержание Passport V

































































































































































































































































































Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды

Mindray Passport V, Руководство по эксплуатации

Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды