Mindray Passport V Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 288

background image

ST Analysis (Optional)

ECG Monitoring

4 - 32

0070- 0-0704-02

Passport V Operating Instructions

4.9.2.1

Adjusting the ISO and J/ST Point

1.

Open the

ST Menu

by using the Navigator Knob to select the ST parameter heading.

ST Menu

can also be

accessed through the

ECG Menu

.

2.

Ensure the

ST Analysis

selection in the

ST Menu

is

On

. The

Passport V

will learn

the patient's QRS complexes (one for a 3-lead leadset or 3 for a 5-lead leadset). These
learned complexes will appear in the

ST Menu

with the monitor-selected

ISO

and

J/ST

points displayed.

3.

Scroll to the

ISO

selection to adjust the isoelectric point on the learned QRS complex.

The isoelectric point is the area of the QRS complex following the P-wave and before the
start of the Q-wave.

4.

Adjust the

ISO

point by pressing the Navigator Knob and turning to adjust the white

ISO

reference line. Press the Navigator Knob when the

ISO

point is satisfactory.

5.

Scroll to the

J/ST

point heading. Adjust the

J/ST

point by pressing the Navigator Knob

and turning to adjust the orange and green

J/ST

reference lines. Press the Navigator

Knob when the

J/ST

points are satisfactory.

6.

To adjust the

ST-pt

, scroll to the

ST-pt

heading and press the Navigator Knob to display

a list of ST measurement point settings. Select the appropriate setting, then press the
Navigator Knob when the

ST-pt

choice is satisfactory.

4.9.2.2

Adjusting ST Measurement Points

ST measurement points refer to ISO point (isoelectric reference point) and ST point. The
Mortara algorithm uses the J+X method to position the ST point, which is located at X position
on the right of J point.

The following table describes the range of ST measurement points and their steps.

ST-pt is set to 60 or 80ms from the J point. When HR is greater than 120 bpm, the distance
between ST point and J point is set at 60ms; when HR is lower or equal to 120 bpm, the
distance between ST point and J point is set at 80ms.

POINT

OPTION/RANGE

STEP

ISO

-200 to -4ms

8ms

J/ST

4 to 200ms

8ms

ST-pt

40ms, 60ms, 80ms,
60/80ms

/

«
...
91
92
93
94
95
...
»

Содержание Passport V

































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Passport V

Бренд: Waterpik Страницы: 16

Water Flosser WF-03

Бренд: Waterpik Страницы: 48

Бренд: Waterpik Technologies Страницы: 20

Бренд: Ossur Страницы: 50

Бренд: juwel Страницы: 12

Бренд: Copper Fit Страницы: 4

Wireless Leash GT Series

Бренд: Unleashed Страницы: 16

Бренд: Live Fine Страницы: 13

Бренд: 4pets Страницы: 2

Бренд: OBUSFORME Страницы: 12

Бренд: GENDRON Страницы: 35

Бренд: GoBone Страницы: 12

Бренд: GO LITE Страницы: 45

Бренд: Coala Life Страницы: 6

Unblemished Wand

Бренд: Unblemished Beauty Страницы: 7

Бренд: Cambridge Temperature Concepts Страницы: 43

Бренд: Tri-Tronics Страницы: 26

Бренд: D.T.Systems Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды