Mindray Passport V Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 288

background image

Passport V Operating Instructions

0070- 0-0704-02

6 - 11

SpO2 Monitoring

SpO

2

Troubleshooting and SpO

2

Menu Performance Considerations

6.5

SpO

2

Troubleshooting and SpO

2

Menu

Performance Considerations

To ensure optimal performance, use an appropriate sensor, apply it as directed and observe
all warnings and cautions.

If excessive ambient light is present, cover the sensor site with opaque material. Failure to do
so may result in inaccurate measurements. Light sources that can affect performance include
surgical lights, especially those with a xenon light source, bilirubin lamps, fluorescent lights,
infrared heating lamps, and direct sunlight.

In the event that you are unable to get a reading, or the reading you get is inaccurate,
consider the following:

• If your patient is poorly perfused, try applying the sensor to another site - such as a

different finger or toe.

• Check that the sensor is properly aligned.

• In electrosurgery, make sure sensor is not too close to ESU devices or cables.

• Check to make sure the site area is clean/non-greasy. Clean site and sensor if needed.

CAUTION:

A functional tester cannot be used to assess the accuracy of
the pulse oximeter probe or a pulse oximeter monitor.

NOTE:

If the supply mains has been interrupted during SpO

2

monitoring, the Passport V will switch power to battery
backup if at least one battery has been installed and
charged. If power has been completely interrupted, SpO

2

monitoring will continue when the supply mains is restored
or a fully charged battery is installed, and power has been
recycled to the monitor.

PROBLEM

REASON

SOLUTION

Unable to obtain SpO

2

reading

Patient has poor perfusion.

Switch limbs / Notify
physician.

Sensor not on Patient.

Reapply sensor.

Cables loose / not
connected.

Check connections, switch
cable.

Ambient light.

Switch limbs and cover
sensor with opaque material.

No SpO

2

waveform

Waveform not selected to
Display.

Go to the

Display Setup

Menu

, choose to display

Pleth

in the waveform area.

Cable or sensor not
plugged in.

Check cable and sensor.

«
...
112
113
114
115
116
...
»

Содержание Passport V

































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Passport V

Бренд: Darco Страницы: 2

splash with 5STAR

Бренд: GreatCall Страницы: 10

Бренд: Vertex Страницы: 16

Бренд: TensCare Страницы: 114

Бренд: Sota Страницы: 12

Бренд: Morphy Richards Страницы: 1

Бренд: Ormed Страницы: 253

Staywell 900 Series

Бренд: Petsafe Страницы: 44

Бренд: Trixie Страницы: 2

Reveal Heated Eyelash Curler EC300

Бренд: Remington Страницы: 78

Бренд: Silk'n Страницы: 110

Бренд: Viora Страницы: 23

Бренд: Xiaomi Страницы: 14

Бренд: Cli-mate Страницы: 8

HANG 'N' LOCK MADISON WC147369E

Бренд: Croydex Страницы: 8

KittySalon Groomer

Бренд: Watchorn Products Страницы: 4

BALL TRAINER Series

Бренд: Dogtra Страницы: 2

Elle Macpherson The Body ELM-FS300-GB

Бренд: HoMedics Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды