Mindray Passport V Скачать руководство пользователя страница 112

Страница: 112 / 288

Passport V Operating Instructions

0070- 0-0704-02

6 - 9

SpO2 Monitoring

SpO

Pulse Oximetry

6.4.3

DPM SpO

The digital SpO

value displays on the SpO

LED (7), and the SpO

Pulse Rate displays on

the Pulse Rate LED (6).

CAUTION:

When equipped with DPM SpO2, use only DPM oxygen
sensors and cables. Use of other oxygen sensors may cause
improper oximeter performance.

NOTE:

Refer to instructions included with each SpO

sensor and

cable for proper placement and use.

NOTE:

Consideration should be given to the disposal of packaging
waste.

Select an SpO

sensor that is appropriate for the patient size.

Attach the connector of the SpO

sensor to the SpO

extension cable.

Attach the SpO

sensor to the patient’s finger (or other appropriate site).

Align the key slot on the connector on the end of the SpO

extension cable with the

SpO

receptacle on the right side panel of the

Passport V

. Push the connector into the

SpO

receptacle until a “click” is heard. The SpO

measurement displays when the

Passport V

detects that the sensor is connected to the patient. A plethysmogram

displays to the left of the SpO

numeric tile (if SpO

is selected in the TRACE SETUP

menu).

NOTE:

To disconnect the cable from the Passport V, pull straight out
on the collar of the connector marked with two arrows.

Monitoring with a Reusable Y Sensor (Adult and Pediatric)

The reusable Y SpO

sensor consists of the sensor and its sheath. One side of the sensor has

an LED with an infrared detector and the other side has a pulse detector.

Insert the LED and pulse detector ends of the Y SpO

sensor into the respective grooves

of the sheath (see FIGURE 6-4 and F IGURE 6-5).

FIGURE 6-4

Inserting the Y SpO

sensor into the sheath

Содержание Passport V

































































































































































































































































































Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды

Mindray Passport V, Руководство по эксплуатации

Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды