Mindray Passport V Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 288

background image

Keys and Front Panel

General Product Description

1 - 6

0070- 0-0704-02

Passport V Operating Instructions

13. Print Trend

Press this key to initiate printing of the displayed trend. By default, the monitor’s stored trend
information will be printed by the internal printer. Pressing this key during a print job will
abort printing.

• If the print destination is a remote Central Station, then pressing this key will initiate a

trend report at the Central Station.

• If the print destination is a remote printer, then pressing this key will initiate a trend report

at the remote printer.

14. Standby

Press this key to place the

Passport V

into a STANDBY mode. While in STANDBY mode,

monitoring is discontinued and the alarms are in permanent suspension, interval NIBP
measurements are placed in idle mode, CO

2

pump is shut off, and the display shuts down.

The monitor notifies the central station and other monitors.

Except for the power on/off switch

and the STANDBY key, all the other hard keys on the front panel are disabled. When in the
STANDBY mode, the message

To Begin Monitoring, press Standby.

is displayed.

NOTE:

Trend data is not cleared in the STANDBY mode. When the
STANDBY mode is released, NIBP INTERVAL is in IDLE MODE
and requires reactivation via the START key. The CO

2

pump

automatically reactivates if the DPM or Microstream

®

sensor

is in place.

Press the

Standby

key to exit the STANDBY mode and return to the normal screen. When

exiting from the standby mode to the monitoring mode, the monitor responds as follows:

• Restores parameter measurement: Start arrhythmia relearning. Gas modules recover the

working status before the standby mode. NIBP measurement will not start automatically.

• Restores normal data storage.

• All the alarms are activated.

• The screen becomes the one displayed before the standby mode.

• The function of auxiliary output is restored.

• The functions of input devices (such as the hard keys on the front panel) are activated.

• The monitor notifies the central station and other monitors.

15. Discharge

Press this key to discharge a patient.

16. Mark Event

Press this key to cause a time stamp event marker to be noted in the trend memory.

17. Trends

Press this key repeatedly to toggle through the following screens:

Quick Trend

,

List Trend

,

Graphic Trend

, and normal screen (or

OxyCRG

, if the patient size is set to Neonate).

18. Normal Screen

Press this key at any time to return the screen to the normal monitoring mode. All menus are
closed.

«
...
27
28
29
30
31
...
»

Содержание Passport V

































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Passport V

Бренд: Davita Страницы: 17

Бренд: Source Страницы: 31

Бренд: Dreamlight Страницы: 40

Бренд: Merula Страницы: 48

Бренд: SportDOG Страницы: 117

FKB 300541 Series

Бренд: UNITED ORTHO Страницы: 2

Бренд: Ouraring Страницы: 8

Бренд: Weelko Страницы: 25

Hydracare Hydracup v1.0

Бренд: AQUARATE Страницы: 28

Бренд: INVISIBLE FENCE Страницы: 16

Бренд: Live Fine Страницы: 13

Staywell 300 Series

Бренд: Petsafe Страницы: 12

Бренд: LitterMaid Страницы: 17

Бренд: Clarisonic Страницы: 30

Healthy Pet Simply Feed

Бренд: Petsafe Страницы: 2

Happy Ride 62349

Бренд: Petsafe Страницы: 12

Бренд: Nature's Miracle Страницы: 20

Бренд: Viatom Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды