Mindray Passport V Скачать руководство пользователя страница 197

Страница: 197 / 288

Prompt Messages

Messages

14 - 20

0070- 0-0704-02

Passport V Operating Instructions

14.3.12

Configuration Management

Table of Configuration Transfer Messages

14.3.13

Network

MESSAGE

REASON

SOLUTION

Monitor log export error

Exporting log error.

Check the storage device and
retransfer log data.

Exporting Monitor Logs

Remain in the state of exporting
logs..

No handling needed.

Monitor log export complete

Exporting log data finishes.

No handling needed.

MESSAGE

REASON

SOLUTION

Monitor defaults transfer
error

Configuration data transfer
error.

Check the storage device and
retransfer the configuration
data.

Downloading Monitor
Defaults

Remain in the state of
configuration data
downloading.

No handling needed.

Uploading Monitor Defaults

Remain in the state of
configuration data uploading.

No handling needed.

Monitor defaults download
complete

Configuration data downloading
finishes.

No handling needed.

Monitor defaults upload
complete

Configuration data uploading
finishes.

No handling needed.

Loading configuration failed.

Loading user configuration or
latest configuration failed.

No handling needed.

ALARM MESSAGE

REASON

SOLUTION

IP Address Conflict

The IP address set in the monitor
is same with that set in other
monitors covered in the same
network.

Change the IP address of the
monitor.

Viewed Monitor is Currently
in Demo Mode.

Viewed bed is in demo mode.

No handling needed.

Содержание Passport V

































































































































































































































































































Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды

Mindray Passport V, Руководство по эксплуатации

Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды