Mindray Passport V Скачать руководство пользователя страница 19

Страница: 19 / 288

IntroductionAvoid simultaneous contact with the patient and the SP1 and SP2 ports on the Passport V to avoid excessive leakage current.

xvi

0070- 0-0704-02

Passport V Operating Instructions

CAUTION:

Devices connected to the Passport V must meet the
requirements of the applicable IEC standards (e.g., IEC 60950

safety standards for information technology equipment and IEC

60601-1 safety standards for medical electrical equipment). The
system configuration must meet the requirements of the IEC

60601-1-1 medical electrical systems standard. Any personnel

who connects devices to the signal input/output port of the
Passport V is responsible for providing evidence that the safety

certification of the devices has been performed in accordance to

the IEC 60601-1-1. Please contact Technical Support if you have
any questions about connecting devices to the data port.

CAUTION:

The Gas Module must be power cycled if the Passport V monitor
is powered off.

Avoid simultaneous contact with the patient and the SP1 and SP2 ports on the
Passport V to avoid excessive leakage current.

Notes

NOTE:

This unit is not designed to be used with a peripheral pulse

sensor. SpO

is a standard function in this monitor, and may be

used to obtain a plethysmograph waveform and heart rate.

NOTE:

The comparison testing conducted via the auscultatory method

used both Phase 4 and Phase 5 Korotkoff sounds. Reports of

study findings for both the auscultatory method as well as the
intra-arterial methods are available by contacting Technical

Support (800) 288-2121, ext. 8116 or (201) 995-8237.

NOTE:

Potential hazards due to errors in software or hardware have

been minimized by actions taken in accordance with IEC 60601-
1-4.

Содержание Passport V

































































































































































































































































































Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды

Mindray Passport V, Руководство по эксплуатации

Результаты поиска

Содержание Passport V

Отзывы:

Похожие инструкции для Passport V

Бренды по названию

Популярные бренды