Lucent Technologies Lineage 2000 J85503B-2 Скачать руководство пользователя страница 81

Страница: 81 / 137

Lucent Technologies Lineage

2000 200A Ferroresonant Rectifier J85503B-2

Issue 8 January 1999

Testing 6 - 9

the RFA and FA LEDs on the control panel and RFA lamp
on the test set light.

2. Turn the Power switch Off, then back On. The rectifier

should start, and the LEDs lights should go off.

3. Repeat Steps (1) and (2) at the F2 and F3 fuses on CM1.

Current Limit

Test

Notes
Adjust the current limit only after verifying that a current limit
problem exists. It is recommended that this test be performed on
battery.

out

is the voltage reading between the rectifier output bus bars.

See Figure 5-3.

1. Connect the test meter to the Test Load bus bar at the

bottom of CB1 and the +V output bus bar.

2. Strap a short across E18 to E33 on CM2, see Figure 6-3.

3. At I

load

= 200-202A, 100 to 101 percent of rated output

current, use the Float Adj potentiometer to adjust V

out

52.08 (26.04) volts.

4. Remove strap from E18 to E33. Observe that V

out

is 51.98

(25.99) to 52.03 (26.0) volts. If not, see Section 7.

5. Increase the load, as indicated on the load box to 218-222

amperes, 110± 1 percent. V

out

should be below 51.58

(25.9) volts. If not, see Section 7.

6. Decrease the load to 192-196A, 96 to 98 percent of the

rectifier rating. Observe that V

out

is greater than 52.03

(26.01) volts.

Phase Failure

Alarm (PHA)

Test

1. Set the load to 100-120A, 50 to 60 percent of the rectifier's

rated amperage.

2. With the Power switch still On, turn off the ac service and

note that the rectifier shuts down and that both the PWR
and MAN lamps on the test set go off.

Содержание Lineage 2000 J85503B-2










































































































































Результаты поиска

Содержание Lineage 2000 J85503B-2

Отзывы:

Похожие инструкции для Lineage 2000 J85503B-2

Бренды по названию

Популярные бренды

Lucent Technologies Lineage 2000 J85503B-2, Руководство по эксплуатации продукта

Результаты поиска

Содержание Lineage 2000 J85503B-2

Отзывы:

Похожие инструкции для Lineage 2000 J85503B-2

Бренды по названию

Популярные бренды