Lucent Technologies Lineage 2000 J85503B-2 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 137

background image

Lucent Technologies Lineage

®

2000 200A Ferroresonant Rectifier J85503B-2

5 - 12 Installation

Issue 8 January 1999

The connectors on the ends of the cable to the ECS controllers
are identical (40-pin), except that the rectifier end has two flying
leads in addition to the connector. The flying leads are labeled
E13 and E14, and connect to those points on the CM2 control
board.

Warning:
If installing a J85503B-2 rectifier with other Lucent
Lineage

®

2000 rectifiers, cut lead 13 of the interface cable of

all rectifiers not equipped with an equalize feature, to
prevent the J85503B-2 rectifier from being placed
permanently in the equalize mode.

1. Route the control cable from the plant controller, via the

cable racks, to the rectifier, through the split bushing
provided for this cable, and through the top of the unit (see
Figure 5-4). Attach a cable tie above the bushing as shown
in Figure 5-3. Excessive cable length must be rolled-up
and tied at the controller, not inside the rectifier.

2. Terminate the 40-pin connector on P5A of CM4 and dress

cable using push-in cable ties on the inside of the rectifier
door. Allow for the door to open and close without putting
stress on the cable. After securing the cable, disconnect the
cable from P5A.

3. Determine the number to be assigned the rectifier in the

rectifier lineup, that is, 1, 2, 3, etc.

4. If the controller is an MCS, cut lead TP0, TP1, TP2 (pins

19, 20, 21) in the controller end of the cable. (See the
controller manual.) This signals to the controller that the
rectifier is a J85503B-2. If the controller is a CCS, do not
cut any lead.

5. Remove the plastic covers on the back of the bay housing

CCS and MCS controllers. The backs of the controllers

Table 5-D: Controller Connectors

Controller

Equipment Code

Connector

Conventional Controlled System (CCS)

J85501A-3

24-pin

Microprocessor Controlled System (MCS)

J85501A-2

24-pin

Evolutionary Control System-6U (ECS-6U)

J85501E-1

40-pin

Evolutionary Control System-12U (ECS-12U)

J85501E-2

40-pin

Galaxy Controller

J85501F-1

40-pin

«
...
60
61
62
63
64
...
»

Содержание Lineage 2000 J85503B-2










































































































































Отзывы:

Нет отзывов

Похожие инструкции для Lineage 2000 J85503B-2

Бренд: ABB Страницы: 9

Бренд: OMCA Страницы: 72

Бренд: Samsung Страницы: 2

Бренд: Warner Electric Страницы: 14

Raven OMNiPOWER NL5000 G5

Бренд: New Leader Страницы: 268

GEH6000IL Series

Бренд: Zimmer Страницы: 67

Бренд: GBC Страницы: 59

Бренд: Novexx Solutions Страницы: 60

Бренд: Falcon Страницы: 8

GKV 20x60 621 AM ELDP

Бренд: GHIELMETTI Страницы: 12

Бренд: Nodka Страницы: 100

Бренд: 3nStar Страницы: 23

Бренд: Enerpac Страницы: 68

Rexroth HAB-4X Series

Бренд: Bosch Страницы: 34

Rexroth LU 2/LS

Бренд: Bosch Страницы: 28

Бренд: Bosch Страницы: 62

Бренд: Bosch Страницы: 30

REXROTH 3 842 528 148

Бренд: Bosch Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды