Lucent Technologies Lineage 2000 J85503B-2 Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 137

background image

Lucent Technologies Lineage

®

2000 200A Ferroresonant Rectifier J85503B-2

Issue 8 January 1999

Troubleshooting and Adjustments 7 - 3

12. Remove the anchoring fasteners from inside the cabinet

base and save for reuse.

13. Four lifting eyebolts, supplied by the customer, must be

securely fastened into the threaded holes in the top corners
of the cabinet.

14. The rectifier is now both electrically and physically

disconnected and, with proper lifting equipment, may be
safely removed from the plant equipment lineup.

Diagnostics

Table 7-A lists possible problems, causes, and solutions that
may occur with the rectifier subsystems. Refer to schematic
drawing SD-83281-01 shipped with the J85503B-2 rectifier.

Table 7-A: Troubleshooting

Problem

Probable Cause

Probable Corrective Action

1. Rectifier will not start and no
indication on front panel. (J5A
should be disconnected. If not,
the controller could be shutting
the rectifier down.)

1. No ac input to rectifier.

1. Check for ac input voltage to
rectifier.

2. Board improperly installed.

2. Check board interlocks and
connections to boards.

2. Rectifier will not start and
gives RFA alarm.

1. CM2 control board is
defective.

1. Check for +27 Vdc between
E13(+) and
E14(-) on CM2. Check for +12
Vdc between E1 and E14 and
-12 Vdc between E3 and E14. If
present, replace the CM2

2. CM7 transformer board is
defective

2. Check wiring associated with
coil of K1 and contacts 4-8 of
K3 on CM7. If bad, replace
CM7.

3. Board improperly installed or
defective ribbon cable.

3. Check board interlocks,
connections to boards, and
ribbon cables.

4. CM3 meter board is
defective.

4. Replace CM3.

5. CM4 interface board is
defective

5. Replace CM4.

3. Rectifier starts but give FA
and RFA alarms.

1. Fuses blown.

1. Check alarm fuses on CM1.
Check filter capacitor fuses.

«
...
99
100
101
102
103
...
»

Содержание Lineage 2000 J85503B-2










































































































































Отзывы:

Нет отзывов

Похожие инструкции для Lineage 2000 J85503B-2

Бренд: National Instruments Страницы: 10

Бренд: Meritor Страницы: 65

Бренд: hager Страницы: 2

Бренд: STEINEL Страницы: 92

Бренд: 4B Страницы: 28

Бренд: AXIOMTEK Страницы: 2

Бренд: DBI SALA Страницы: 32

Бренд: Grundfos Страницы: 58

Бренд: Carrier Страницы: 154

Бренд: Danfoss Страницы: 2

Бренд: Hasler Страницы: 2

BAYCO BC Series

Бренд: Dixon Страницы: 21

Flexiguard 8530595

Бренд: DBI SALA Страницы: 16

Бренд: SCHUNK Страницы: 36

Бренд: EINHELL Страницы: 62

Бренд: ACO Haustechnik Страницы: 90

Бренд: Moeller Страницы: 2

Бренд: Moeller Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды