Lucent Technologies Lineage 2000 J85503B-2 Скачать руководство пользователя страница 90

Страница: 90 / 137

Lucent Technologies Lineage

2000 200A Ferroresonant Rectifier J85503B-2

6 - 18 Testing

Issue 8 January 1999

Phase Failure

Test

1. With the Power switch still On, turn off the ac service and

note that the rectifier shuts down.

2. Verify that no ac voltage is present on the input leads of

the ac contactor K1 (Figure 5-3).

3. Disconnect one input lead, L1, L2, or L3 on K1, or at the

ac service panel, whichever is more convenient. Insulate
the lead.

4. Turn on the ac at the service panel. The rectifier should not

restart.

5. Turn off the ac at the service panel and reconnect the input

lead.

6. Turn on the ac at the service panel. The rectifier should

restart.

Backup High

Voltage

Shutdown

(BUHVSD) Test

1. Turn both the rectifer Power switch and dc output circuit

breaker OFF (down). At the plant controller (if present),
remove the regulation fuse assigned to the rectifier being
tested.

2. Set a DMM to measure 54 volts, and connect it between

the rectifier input conductor at the bottom of CB1 and dc
output return.

3. Slowly turn the Float Adj potentiometer clockwise until

the rectifier shuts down. This should occur at the voltage
corresponding to the switch settings for BUHVSD. The
RFA lamp on the rectifier should light.

4. Turn the Float Adj potentiometer counterclockwise four

turns.

5. Restart the rectifier by turning the Power switch Off then

back On.

6. Adjust the voltage to approximately 52.0 (26.0) volts. The

RFA lamp on the rectifier should go out.

7. Turn OFF the rectifier Power switch once again, and

CLOSE (turn on) the dc output circuit breaker (up) within
5 seconds. Then, at the plant controller (if present), replace

Содержание Lineage 2000 J85503B-2










































































































































Результаты поиска

Содержание Lineage 2000 J85503B-2

Отзывы:

Похожие инструкции для Lineage 2000 J85503B-2

Бренды по названию

Популярные бренды

Lucent Technologies Lineage 2000 J85503B-2, Руководство по эксплуатации продукта

Результаты поиска

Содержание Lineage 2000 J85503B-2

Отзывы:

Похожие инструкции для Lineage 2000 J85503B-2

Бренды по названию

Популярные бренды