Lucent Technologies Lineage 2000 J85503B-2 Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 137

background image

Lucent Technologies Lineage

®

2000 200A Ferroresonant Rectifier J85503B-2

Issue 8 January 1999

Testing 6 - 15

6. Turn rectifier Power switch On. It may be necessary to

readjust the Float Adj potentiometer further clockwise in
order for the rectifier output to return to plant float voltage
and assume any load now that it has changed to external
regulation mode.

Testing On Line

On- and off-line testing require different procedures, although
most tests can be performed in either situation. If you have just
tested the rectifier off line, it is not necessary to repeat the tests
on line.

When testing on-line, connect the rectifier control cable to the
rectifier and to the associated plant controller. Also, install the
rectifier’s associated regulation battery (sense) fuse in the
controller.

If no load is present, connect a test load to the rectifier (page
6-2). Disable load share by setting S1.9 on CM2 to 0.

If the rectifier fails any of the tests in this section, replace the
CM2 board and begin testing again.

Regulation

(NL/FL) Test

Notes
At least two rectifiers must be supplying some current when this
test is done, and the load requirement must be greater than 20A,
10% of the rated output for the rectifier under test.

Do not perform this test with load share enabled.

1. Observe the amperes reading on the Output meter. Hold

the Rect Test switch in the NL position. The output
amperes should decrease.

2. Observe the amperes reading on the Output meter. Hold

the Rect Test switch in the FL position. The output current
should increase.

Rectifier Failure

Alarm/Fuse

Alarm Test

Note
This procedure causes the rectifier to fail and issue alarms to the
plant controller. When the procedure is performed on line,
sufficient rectifiers must be operating to assume the load of the
rectifier being tested.

«
...
85
86
87
88
89
...
»

Содержание Lineage 2000 J85503B-2










































































































































Отзывы:

Нет отзывов

Похожие инструкции для Lineage 2000 J85503B-2

Бренд: Febco Страницы: 12

NESLAB System IV

Бренд: Thermo Scientific Страницы: 22

Бренд: Vahle Страницы: 6

Granudos 45/100-Touch

Бренд: WDT Страницы: 138

Бренд: Mecc Alte spa Страницы: 34

ECO225SL Series

Бренд: Aerotech Страницы: 62

Бренд: Nodka Страницы: 100

Aluminum alternating tread stairs

Бренд: Lapeyre Страницы: 4

Бренд: RSTEEL Страницы: 20

Бренд: Viessmann Страницы: 8

Бренд: Makita Страницы: 2

Бренд: OHTAKE Страницы: 8

Бренд: OEZ Страницы: 6

FO Field Patch set

Бренд: R&M Страницы: 2

Budget SG-24EB Series

Бренд: Shini Страницы: 60

Бренд: Renishaw Страницы: 2

Бренд: Oxford Instruments Страницы: 28

Бренд: Bungard Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды