Lucent Technologies Lineage 2000 J85503B-2 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 137

background image

Lucent Technologies Lineage

®

2000 200A Ferroresonant Rectifier J85503B-2

Issue 8 January 1999

Installation 5 - 11

4. Tape or otherwise insulate the connectors on the end of

each cable that does not terminate in the rectifier. Label
each cable.

5. Place the dc output return cable in cable rack.

6. Insert ends of return cables through top of rectifier and

terminate connector on the positive ground bus bar in the
rectifier. Torque connections to 30 Nm (240 in-lb). See
Figure 5-3.

7. One at a time, remove tape or insulation from connector at

other end of return cable and terminate on plant charge
ground bus bar.

8. Place ungrounded negative output cables in cable rack.

9. Insert ends of charge cables through top of rectifier and

terminate connectors on negative bus bar in rectifier.
Torque to 30 Nm (240 in-lb). See Figure 5-3.

Warning:
Battery plants are an energy hazard. Avoid arc or sparks.
Before making contact between connectors and bus bar in
the next step, use a DMM to verify a true open circuit
between each connector and known battery plant ground.

10. One at a time, remove tape or insulation from connector at

other end of charge cable and terminate on negative charge
bus bar.

Supplemental

Central Office

(CO) Ground

The central office (CO) ground is “daisy-chain” connected to all
rectifiers in a plant and terminates on the central office ground
bus. The ground conductor must be 2 AWG wire (66,370 cir
mils), or equivalent, for which a lug should be ordered and two
1/4-20 bolts are provided. Connect the CO ground to the nearest
connection point on top of the rectifier (see Figure 5-4). Torque
to 8 Nm (65 in-lb).

Plant Control

Cable Assembly

(Lucent

Controller)

All cables connecting Lucent controllers to this rectifier, have a
40-pin connector on the rectifier end, which terminates on
connector P5A of the CM4 interface board inside the rectifier
door. (See Figures 2-3, 5-3, and 5-6.) Table 5-D provides the
type of connector used to connect the cable to the controller.

«
...
59
60
61
62
63
...
»

Содержание Lineage 2000 J85503B-2










































































































































Отзывы:

Нет отзывов

Похожие инструкции для Lineage 2000 J85503B-2

Бренд: Vaillant Страницы: 76

Бренд: X-FLOC Страницы: 35

Бренд: Eaton Страницы: 2

Бренд: Aloxy Страницы: 34

Бренд: Gabocom Страницы: 4

Бренд: Magnum Industrial Страницы: 10

Бренд: Canrig Страницы: 6

Бренд: MPS Страницы: 2

Бренд: OIC Korea Страницы: 12

7x7 NG Plus 4 Series

Бренд: Monosem Страницы: 94

Бренд: THORLABS Страницы: 29

Бренд: SCHUNK Страницы: 36

Бренд: Parker Страницы: 8

Heavy Duty Dust Buggy

Бренд: U.S.SAWS Страницы: 18

PACSystems RXi Series

Бренд: GE Страницы: 8

Бренд: IEI Technology Страницы: 156

AVTRON LOADBANK LPH400

Бренд: Emerson Страницы: 33

Бренд: Emerson Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды