Lucent Technologies Lineage 2000 J85503B-2 Скачать руководство пользователя страница 111

Страница: 111 / 137

Lucent Technologies Lineage

2000 200A Ferroresonant Rectifier J85503B-2

Issue 8 January 1999

Troubleshooting and Adjustments 7 - 13

b. If the rectifier Float Adj potentiometer can be used to

adjust the voltage to the correct level, the RFA problem
has been cleared. Otherwise, continue with the
following procedures.

3. If the rectifier output voltage is less than the plant voltage

and/or all rectifiers shut down, then use the following
procedures.

a. If the CM2 board has not been replaced, then replace it

at this time.

b. If the rectifier started, minor alarm retired on controller,

and the rectifier RFA light extinguished, then the RFA
problem has been cleared. Otherwise, continue with the
following procedures.

4. If replacing the CM2 board does not clear the problem,

then the outputs from T1 and T2 are probably unbalanced.
Try the following:

a. Check the wiring to the thyristors (see Figure 8-1).

b. Check for defective thyristors. If defective, replace.

5. Verify that the controller's high voltage shutdown circuit is

operating properly (see the controller manual).

Clear Fuse

Alarm (FA)

1. If the circuit breaker (CB1) is tripped, restore the rectifier

to service.

2. If CB1 did not trip, check alarm fuses F1, F2, and F3 on

CM1. These fuses are accessible by opening the door of
the rectifier. CM1 is near the output filter capacitors.

3. If the F2 or F3 alarm fuse is blown, check for possible

trouble and replace the fuse.

4. If the F1, F2, F3, F4, or F5 capacitor fuse or F1 alarm fuse

on CM1 is blown, check for a shorted output capacitor.
Remove the rectifier from service to replace any shorted
capacitor and/or blown fuse.

Содержание Lineage 2000 J85503B-2










































































































































Результаты поиска

Содержание Lineage 2000 J85503B-2

Отзывы:

Похожие инструкции для Lineage 2000 J85503B-2

Бренды по названию

Популярные бренды

Lucent Technologies Lineage 2000 J85503B-2, Руководство по эксплуатации продукта

Результаты поиска

Содержание Lineage 2000 J85503B-2

Отзывы:

Похожие инструкции для Lineage 2000 J85503B-2

Бренды по названию

Популярные бренды