Lucent Technologies Lineage 2000 J85503B-2 Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 137

background image

Lucent Technologies Lineage

®

2000 200A Ferroresonant Rectifier J85503B-2

Issue 8 January 1999

Testing 6 - 23

Adjust Rectifiers

as a Group

If the load requirement is always greater than the capacity of
the smallest rectifier, adjust the rectifiers to float voltage using
the following procedure. Rectifiers must be on line with plant
cables connected and REG fuses installed in the plant controller
or a remote bay.

1. Measure the battery voltage with a test meter connected to

the Plant test jacks.

2. If the battery voltage is not at the predetermined float

voltage or the desired battery float voltage, perform the
following:

a. If the voltage is too high, turn the Float Adj

potentiometer counterclockwise on the rectifier with the
highest output current.

b. If the voltage is too low, turn the Float Adj

potentiometer clockwise on the rectifier with the lowest
output current.

3. Check the battery voltage and repeat Steps (a) and (b)

above until the battery voltage is within the required
tolerance of the desired float voltage.

4. If all rectifiers are not carrying some load current (between

5 percent and 95 percent of rated load), perform the
following:

Note
Rectifiers are not required to share load current equally unless
load share is enabled.

a. Turn off all spare rectifiers, but leave enough rectifiers

on to handle the load current.

b. Turn up (clockwise) the Float Adj potentiometer on

rectifiers carrying less than 5 percent rated load till they
carry more than 5 percent rated load, and

c. Turn down (counterclockwise) the Float Adj

potentiometer on rectifiers carrying more than 95
percent rated load until they carry less than 95 percent
rated load.

«
...
93
94
95
96
97
...
»

Содержание Lineage 2000 J85503B-2










































































































































Отзывы:

Нет отзывов

Похожие инструкции для Lineage 2000 J85503B-2

Бренд: TDW Страницы: 2

Бренд: ABB Страницы: 4

Бренд: MAKSIWA Страницы: 155

Бренд: Facom Страницы: 44

Z33-D060.12 S15A

Бренд: Jäger Страницы: 36

Evaluation kit 60 V

Бренд: TDK Страницы: 28

SEC-2000 Series

Бренд: Vecow Страницы: 84

Бренд: CKD Страницы: 37

ebro EBI DA Set

Бренд: Xylem Страницы: 8

Kontron KBox A-203-sXAL4

Бренд: S&T Страницы: 64

Бренд: T-Drill Страницы: 80

DT FEA H-ST NC Series

Бренд: RINGSPANN Страницы: 22

Бренд: RINGFEDER Страницы: 24

Бренд: Belmash Страницы: 80

Бренд: SCHUNK Страницы: 77

PS 20 NON STOP+

Бренд: Meler Страницы: 100

CANVASA II + II

Бренд: Leibinger Страницы: 83

Бренд: Chai Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды