Lucent Technologies Lineage 2000 J85503B-2 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 137

background image

Lucent Technologies Lineage

®

2000 200A Ferroresonant Rectifier J85503B-2

2 - 4 Product Description

Issue 8 January 1999

For operation without batteries, the sense point voltage remains
within 10 percent of its setting and returns and remains in the 2
percent band within 500 milliseconds for any step load change
of 50 to 90 percent, or 90 to 50 percent, or a step change of 10
percent of the input voltage.

Forced

Electronic Load

Sharing

The rectifier is equipped with a user selected option by which the
rectifier is capable of load sharing with other J85503B-2
rectifiers to better than 10 percent of the full load rating of the
rectifier.

Safety Interlocks

A series-loop circuit electrically interconnects all of the circuit
modules and prevents rectifier operation if any circuit module is
not properly installed.

Restart Circuit

The rectifier is compatible with the automatic restart features of
Lineage

®

2000 controllers. The rectifier will also accept an

isolated restart signal from any external source via the interface
board.

Output Circuit

Breaker

An output circuit breaker protects the plant from rectifier
malfunction and excessive current, and may be used to
disconnect the rectifier from the battery. The standard breaker
size is 215 amperes.

Output Current

Indication

A precision resistor shunt measures the rectifier output current.
When used with a Galaxy or Microprocessor Controlled System
controller, the rectifier provides an isolated 2- to 10-volt signal,
corresponding to a range of no-load to 125 percent of rated
output load, to indicate the rectifier drain on the controller. In
addition, shunt access points are available on the 329A board for
measuring the shunt voltage directly.

Output Voltage

Adjustment

Range

The rectifier is capable of providing up to 65 volts dc (or ±32
volts dc in ±24 volt plants) output at 50 percent of its rated output
power and nominal input voltage.

Float/Equalize/

Boost

The rectifier can be put into the Equalize mode in one of three
ways:

«
...
20
21
22
23
24
...
»

Содержание Lineage 2000 J85503B-2










































































































































Отзывы:

Нет отзывов

Похожие инструкции для Lineage 2000 J85503B-2

Бренд: Daikin Страницы: 12

Бренд: Napoleon Страницы: 3

Бренд: Daikin Страницы: 52

Бренд: Graco Страницы: 46

Бренд: SCHUNK Страницы: 24

Бренд: Eaton Страницы: 2

Power Defense PD4

Бренд: Eaton Страницы: 7

Бренд: a-TroniX Страницы: 8

Бренд: Sensor Networks Страницы: 22

Бренд: VEMAG Страницы: 167

Бренд: Grizzly Страницы: 44

Бренд: VETEC Страницы: 16

Бренд: Atlas Страницы: 36

Бренд: SIGLENT Страницы: 7

Бренд: SCHUNK Страницы: 40

Бренд: Kuzar Страницы: 24

Бренд: Emerson Страницы: 12

Бренд: Emerson Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды