Lucent Technologies Lineage 2000 J85503B-2 Скачать руководство пользователя страница 92

Страница: 92 / 137

Lucent Technologies Lineage

2000 200A Ferroresonant Rectifier J85503B-2

6 - 20 Testing

Issue 8 January 1999

5. Repeat Steps 1 and 2 on:

MCS or CCS: TB1-32 to test rectifiers 7, 8, 15, and 16
(MCS) or 13, 14, 15, and 16 (CCS).

ECS-6U and ECS-12U: TB101-12 to test rectifiers 4
(8 and 12, ECS-12U).

Galaxy: TB3-11 to test rectifiers 7, 8, 15, 16, 23, and
24.

Selective High

Voltage

Shutdown

(SHVSD) and

Restart

Warning
This procedure is safe only if the using equipment can tolerate
the higher voltage.

1. Using the Float Adj potentiometer, raise the rectifier

voltage to the SHVSD level of the controller.

2. Adjust the load so the rectifier delivers 20-30A, 10 to 15

percent of its rated amperage.

3. The rectifier should shut down, and the RFA LED on the

control panel should light.

4. Observe that the rectifier restarts after 4 seconds and shuts

down again. With an MCS controller, a second restart may
occur.

5. Adjust rectifier back to its proper setting. Turn the unit off,

then back on. The rectifier should restart and RFA lamp
should go off.

AC Fail Test

This test must be done on battery, with CB1 on.

1. Turn off the ac service to the rectifier. The ACF LED on

the control panel should light and an ac fail alarm should
be generated on TB3-3 and TB3-4 of CM4.

2. Restore ac to the rectifier.

Содержание Lineage 2000 J85503B-2










































































































































Результаты поиска

Содержание Lineage 2000 J85503B-2

Отзывы:

Похожие инструкции для Lineage 2000 J85503B-2

Бренды по названию

Популярные бренды

Lucent Technologies Lineage 2000 J85503B-2, Руководство по эксплуатации продукта

Результаты поиска

Содержание Lineage 2000 J85503B-2

Отзывы:

Похожие инструкции для Lineage 2000 J85503B-2

Бренды по названию

Популярные бренды