Lucent Technologies Lineage 2000 J85503B-2 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 137

background image

Lucent Technologies Lineage

®

2000 200A Ferroresonant Rectifier J85503B-2

2 - 10 Product Description

Issue 8 January 1999

rectifier goes to maximum current (FL); when it is operated to
NL, the rectifier goes to no current.

Rect + and - Test

Jacks

The Rect + and - test jacks allow for measuring the output
voltage of the rectifier.

Plant + and -Test

Jacks

The Plant + and - test jacks measure the voltage between the
points where the remote sense leads are connected. This
measurement is accurate only when the remote sense leads are
connected.

Float Adj

The Float Adj potentiometer provides for manual adjustment of
the output float voltage.

FLT/EQ

The Float/Equalize, FLT/EQ, switch allows the user to select
either the float or equalize operating mode. This switch is
disabled when the rectifier is shipped from the factory and must
be enabled via S2.1 of the 330C interface board in order to
provide the local equalize feature. The yellow equalize LED
lights when the rectifier is in the equalize mode.

Equal Adj

The Equal Adj potentiometer provides for manual adjustment
of the output equalize voltage.

Circuit Breaker

The circuit breaker protects the plant from rectifier malfunction
and excessive current, and may be used to disconnect the
rectifier from the battery. When the circuit breaker trips
(midway between On and Off) because of excessive current, an
alarm is transmitted to the plant controller. When the circuit
breaker is manually turned off, no alarm is transmitted.

Circuit Modules

The rectifier’s signal processing and control circuitry are located
on replaceable circuit modules or packs. Circuit modules are
plug-in boards that are ordered separately. (See Section 3 for
ordering information.) All modules are accessible by opening
the rectifier door. Figure 2-3 shows the location of the modules
and other features of the rectifier. Figures 6-2, 6-3, 7-1, and 5-6
show the CM1 through CM4 board layouts, respectively. A
description of each module follows.

«
...
26
27
28
29
30
...
»

Содержание Lineage 2000 J85503B-2










































































































































Отзывы:

Нет отзывов

Похожие инструкции для Lineage 2000 J85503B-2

Бренд: Eaton Страницы: 2

Бренд: Terrier Страницы: 36

sepro ROBOTIQUE

Бренд: Axess Страницы: 44

Бренд: Siruba Страницы: 30

Бренд: CKD Страницы: 37

eBOX671-521-FL Series

Бренд: AXIOMTEK Страницы: 2

Бренд: Pfeiffer Vacuum Страницы: 16

Z80-H460.03 S5W2/2

Бренд: Jäger Страницы: 36

Aseptic INNOVA Mini K

Бренд: INOXPA Страницы: 28

Бренд: Aaeon Страницы: 42

Бренд: OEZ Страницы: 13

Бренд: Advantech-DLoG Страницы: 52

Бренд: CLEAN ROOM DEVICES Страницы: 16

Бренд: Siemens Страницы: 4

3ZX1812-0WX31-9DN1

Бренд: Siemens Страницы: 6

Бренд: Siemens Страницы: 4

Бренд: Siemens Страницы: 5

Бренд: Siemens Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды