Lucent Technologies Lineage 2000 J85503B-2 Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 137

background image

Lucent Technologies Lineage

®

2000 200A Ferroresonant Rectifier J85503B-2

Issue 8 January 1999

Testing 6 - 19

the regulation fuse assigned to the rectifier being tested.
(This is the fuse removed in Step 1.) Now, turn ON the
rectifer Power switch once again, and turn the Float Adj
potentiometer on the front display clockwise to return the
rectifier output voltage to the plant float voltage level
where it accepts load from any other rectifiers also on the
distribution bus.

Control (TR) Test

1. a.

MCS or CCS: Place a ground on lug 29 of TB1 in the
MCS or CCS controller to turn off rectifiers 1 and 2
(MCS 9 and 10, CCS 3 and 4) via the TR signal. The
rectifiers should turn off.

b.

ECS-6U or ECS-12U: Place a ground on TB101-9 in
the ECS controller to turn off rectifiers 1 and 5 (and 9
in ECS-12U) via the TR signal. The rectifier(s) should
turn off.

c.

Galaxy: Place a ground on TB3-8 in the Galaxy
controller to turn off rectifiers 1, 2, 9, 10, 17, and 18
via the TR signal. The rectifier(s) should turn off.

2. Remove the ground. The rectifier(s) should turn on.

3. Repeat Steps 1 and 2 on:

a.

MCS or CCS: TB1-30 to test rectifiers 3, 4, 11, and 12
(MCS) or 5, 6, 7, and 8 (CCS).

b.

ECS-6U and ECS-12U: TB101-10 to test rectifiers 2
and 6 (and 10, ECS-12U).

c. Galaxy: TB3-9 to test rectifiers 3, 4, 11, 12, 19, and

20.

4. Repeat Steps 1 and 2 on:

a.

MCS or CCS: TB1-31 to test rectifiers 5, 6, 13, and 14
(MCS) or 9, 10, 11, and 12 (CCS).

b.

ECS-6U and ECS-12U: TB101-11 to test rectifiers 3
(7 and 11, ECS-12U).

c.

Galaxy: TB3-10 to test rectifiers 5, 6, 13, 14, 21, and
22.

«
...
89
90
91
92
93
...
»

Содержание Lineage 2000 J85503B-2










































































































































Отзывы:

Нет отзывов

Похожие инструкции для Lineage 2000 J85503B-2

Бренд: Armarge Страницы: 12

MAXI-MIXER 4400 TRAILER

Бренд: SAC Страницы: 56

Бренд: Valor Страницы: 65

NZM3-XSH-48-NA Series

Бренд: Eaton Страницы: 6

Бренд: Climax Страницы: 50

FlashPac LS-1130

Бренд: Excelitas Technologies Страницы: 13

Бренд: Wachs Страницы: 52

dynasafe Mecha 3.2

Бренд: Tractel Страницы: 56

Бренд: Wieland Страницы: 40

Бренд: ABB Страницы: 112

Бренд: RINGSPANN Страницы: 16

Бренд: Eaton Страницы: 16

Бренд: AuCom Страницы: 24

Radicon G Series

Бренд: Benzlers Страницы: 28

FEEDER CUBE FC-40 Plus Series

Бренд: Rodix Страницы: 4

Бренд: Zephyr Страницы: 40

GQM22M5C2H910JB01 Series

Бренд: Murata Страницы: 25

GQM22M5C2H7R0CB01 Series

Бренд: Murata Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды