Lucent Technologies Lineage 2000 J85503B-2 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 137

background image

Lucent Technologies Lineage

®

2000 200A Ferroresonant Rectifier J85503B-2

Issue 8 January 1999

Product Description 2 - 9

•

The rectifier output voltage when the meter switch is in the
Rect V position

•

The battery voltage when the meter switch is in the Plt V
position

Rect V

The user may select whether the default position of the meter
switch is rectifier current or battery voltage. Otherwise, moving
the switch momentarily to the Rect V position displays the
rectifier voltage. The user may also select the option of having
the meter active when the rectifier is manually turned off.

Power Switch

The Power switch turns the rectifier On, Off, or puts it in the
Auto mode for remote control via a signal to the interface board.
A green LED lights when the rectifier is on.

Alarms

The control panel on the J85503B-2 has the following LEDs:

PHA: A red LED lights if the rectifier shuts down due to phase
voltages falling below the normal operating range or total loss of
a phase

FA: A red LED lights if any fuse, except the LSF fuse, operates
or the output circuit breaker operates

RFA: A red LED lights if a failure occurs in the rectifier and the
rectifier shuts down

LSF: A yellow LED lights if the fuse in the load share circuit of
the rectifier operates

LCA: A yellow LED lights if the load share option is active and
the rectifier is providing less than 1.5 amperes of output current.
The LED remains on until output reaches 6 amperes.

ACF: A red LED lights if commercial ac fails.

Rect Test Switch

The Rect Test switch provides a manual test of the rectifier
regulation by simulating a full load (FL) or no load (NL)
condition. Operating the switch raises or lowers the output
voltage setting of the rectifier by 0.25 volt when on battery.
When the switch is in the center position, the rectifier is in the
normal operating state; when the switch is operated to FL, the

«
...
25
26
27
28
29
...
»

Содержание Lineage 2000 J85503B-2










































































































































Отзывы:

Нет отзывов

Похожие инструкции для Lineage 2000 J85503B-2

Бренд: ACS Страницы: 56

Tetrix 351 AC/DC Smart FW

Бренд: EWM Страницы: 117

Power Xpert C445

Бренд: Eaton Страницы: 2

Бренд: Nederman Страницы: 89

Бренд: Nederman Страницы: 71

Бренд: Nederman Страницы: 131

GED5000IL Series

Бренд: Zimmer Страницы: 52

Бренд: Ground Fault Systems Страницы: 26

Бренд: Kärcher Страницы: 188

SANDBLASTER SLS

Бренд: SINTERIT Страницы: 20

Бренд: Eaton Страницы: 2

Бренд: Covaris Страницы: 57

DS-K3B601SX Series

Бренд: HIKVISION Страницы: 56

Бренд: SCHUNK Страницы: 2

Liebert Maintenance Bypass Cabinet

Бренд: Vertiv Страницы: 36

Бренд: WTE Страницы: 60

Бренд: Grizzly Страницы: 24

Бренд: Omron Страницы: 130

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды