Lucent Technologies Lineage 2000 J85503B-2 Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 137

background image

Lucent Technologies Lineage

®

2000 200A Ferroresonant Rectifier J85503B-2

6 - 8 Testing

Issue 8 January 1999

Testing Off
Line

The following tests involve use of the test load and a Battery
Plant Simulator Test Set. Refer to page 6-2 for the procedure to
connect a test load and pages 6-2 and 6-3 for a Battery Plant
Simulator Test Set.

If the rectifier fails any of the tests in this section, replace the
CM2 board and begin testing again.

Startup

1. Turn on the ac supply to the rectifier. The PWR lamp on

the test set should light brightly. If it does not light
properly, check the connection of the two small red and
black clip leads. They may be reversed or otherwise
incorrectly connected. These leads provide the operating
voltages in the test set, and the red lead should be
approxi27 volts dc with respect to the black lead.

2. The PWR lamp should remain lit during the remaining

tests as long as the ac supply is turned on.

3. Set the test meter to the 100 volts range, and connect it to

the Rect jacks on the rectifier control panel. (See Figure
2-2.)

4. Adjust the test load so that when the rectifier is turned on,

it will deliver 10-40A, 5 to 20 percent of full load.

5. Place the S1 switch on CM4 in the LOC position (see

Figure 5-5), and turn the Power switch On. The rectifier
should start and the green Power LED on the front panel
should light. The test meter should indicate 40-50 or 22-26
volts. The MAN lamp on the test set should light and
remain lit as long as the rectifier is turned on.

Regulation

(NL/FL) Test

1. Watch the test meter and move the Rect Test switch to

NL. In the NL position, the voltage should drop between
0.3 and 0.6 volt.

2. Repeat Step 1 with the Rect Test switch in the FL position.

The voltage should increase between 0.1 and 0.4 volt.

Rectifier Failure

Alarm Test

1. Holding the insulation on a piece of bare wire or the end of

a paper clip, insert the wire into the fuse holder of the F1
alarm fuse on CM1. Note that the rectifier shuts down, and

«
...
78
79
80
81
82
...
»

Содержание Lineage 2000 J85503B-2










































































































































Отзывы:

Нет отзывов

Похожие инструкции для Lineage 2000 J85503B-2

MobilGate - 128c

Бренд: SeaSoft Страницы: 11

Бренд: Commercial Electric Страницы: 2

Бренд: Bondura Страницы: 10

Бренд: WPG Страницы: 4

BNI CCL-502-100-Z001

Бренд: Balluff Страницы: 193

Бренд: AEMC instruments Страницы: 12

Бренд: 4B Страницы: 28

Бренд: AXIOMTEK Страницы: 2

BTL5-A11-M Series

Бренд: Balluff Страницы: 18

Бренд: Kitagawa Страницы: 32

Бренд: Zimmer Страницы: 44

Бренд: Graco Страницы: 87

Бренд: Lippert Components Страницы: 10

Бренд: WABROTECH Страницы: 20

Бренд: Bosch Страницы: 64

X-Vac Hydro Excavator X15 Series

Бренд: Hi-Vac Страницы: 87

Бренд: ABB Страницы: 10

Бренд: ABB Страницы: 130

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды