Lucent Technologies Lineage 2000 J85503B-2 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 137

background image

Lucent Technologies Lineage

®

2000 200A Ferroresonant Rectifier J85503B-2

Issue 8 January 1999

Installation 5 - 19

via the regulation leads. If the settings are changed, the voltage
is regulated at the output terminals of the rectifier.

S3.1 through S3.4 adjust the level of the backup high voltage
shutdown (BUHVSD). See Table A of Figure 5-8 for the range
of BUHVSD settings. The factory setting is 59.5 Vdc for 48 volt
rectifiers or 30.25 Vdc for 24 volt rectifiers.

S3.5 and S3.6 are factory settings that notify the control circuit
that the rectifier is configured as a 48 or 24 volt rectifier.

S3.7 and S3.8 permit the internal selective high-voltage
shutdown (ISHVSD) level to be adjusted to 55, 56, 57 or 58
volts. The factory setting is 58 volts.

S3.9 is used to maintain voltage stability when the current limit
is set below 50% of full load.

S3.10 is not used.

323D Digital

Meter Board

(CM3)

S3.1 through S3.4 tell the rectifier’s ammeters the rectifier's
current capacity.

S3.5 through S3.6 configure the NL/FL switch on the front of the
rectifier for either 24 or 48 volts.

329A Fuse Board

(CM1)

S1.1 through S1.4 are not field adjustable.

330C Interface

Board (CM4)

S2.1 enables the front panel equalize switch on the rectifier.

S2.2 keeps the front panel display on or off when the control
switch is in the off position. When S2.2 is on, the front panel
display is always on. When S2.2 is off, the front panel display is
off when the rectifier is turned off either via the front panel or via
the controller.

S2.3-S2.6 configure the rectifier for operation with a 24- or
48-volt plant.

«
...
67
68
69
70
71
...
»

Содержание Lineage 2000 J85503B-2










































































































































Отзывы:

Нет отзывов

Похожие инструкции для Lineage 2000 J85503B-2

Бренд: MAKSIWA Страницы: 155

MobilGate - 128c

Бренд: SeaSoft Страницы: 11

Бренд: GST Страницы: 2

Precision CPU-H Series

Бренд: Harmonic Drive Страницы: 12

Бренд: Bayer HealthCare Страницы: 56

Бренд: Karibu Страницы: 121

JSE.5-0104MAEAD

Бренд: BRUNEL Страницы: 7

Бренд: Tsubaki Страницы: 3

Бренд: lancer Страницы: 4

Бренд: BIRD Страницы: 24

Бренд: Maggi Страницы: 56

Бренд: M&R Страницы: 62

Бренд: M&C Страницы: 22

HSI150 1x1 GSM110 Varia

Бренд: Hauff-Technik Страницы: 34

Бренд: WEG Страницы: 20

Бренд: Moeller Страницы: 2

Бренд: Moeller Страницы: 4

Бренд: King Young Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды