Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 3

Страница: 3 / 313

Contents

Safety . . . . . . . . . . . . . . . . . . v

Guidelines for trained service technicians . . . . . . vi

Inspecting for unsafe conditions

. . . . . . . vi

Guidelines for servicing electrical equipment. . . vii

Safety statements . . . . . . . . . . . . . . viii
Start here . . . . . . . . . . . . . . . . . . x

Diagnosing a problem

. . . . . . . . . . . x

Undocumented problems . . . . . . . . . xiii

Chapter 1. Introduction . . . . . . . . . 1

Related documentation .  .  .  .  .  .  .  .  .  .  .  .  .  3
Notices and statements in this document .  .  .  .  .  .  4
Features and specifications .  .  .  .  .  .  .  .  .  .  .  4
Blade server controls and LEDs

. . . . . . . . . 7

Scalability indicators .  .  .  .  .  .  .  .  .  .  .  .  .  10
Turning on the blade server .  .  .  .  .  .  .  .  .  .  11
Turning off the blade server .  .  .  .  .  .  .  .  .  .  12
System board layouts .  .  .  .  .  .  .  .  .  .  .  .  12

Blade server connectors - BladeCenter HX5 .  .  12
System-board switches .  .  .  .  .  .  .  .  .  .  13
Blade server connectors - IBM MAX5 .  .  .  .  14
System-board LEDs - BladeCenter HX5 .  .  .  15
System-board LEDs - IBM MAX5 expansion
blade .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  15

Working with a scalable blade complex

. . . . . 16

Chapter 2. Configuring the blade
server. . . . . . . . . . . . . . . . . . 19

Partitioning a scalable blade complex .  .  .  .  .  .  20
Using the Setup utility .  .  .  .  .  .  .  .  .  .  .  .  20
Using the PXE boot agent utility program .  .  .  .  .  24
Using the Boot Selection Menu program .  .  .  .  .  24
Using the Advanced Settings Utility (ASU)

. . . . 25

Updating the Universal Unique Identifier
(UUID). . . . . . . . . . . . . . . . . 25
Updating the DMI/SMBIOS data . . . . . . 27

Using the LSI Logic Configuration Utility
program . . . . . . . . . . . . . . . . . . 29
Updating firmware and device drivers . . . . . . 30

Updating firmware for blade servers operating
as a single partition

. . . . . . . . . . . 31

Updating firmware for each blade server
independently. . . . . . . . . . . . . . 31

Recovering from a UEFI update failure . . . . . . 49

In-band manual recovery method . . . . . . 49
Out-of-band manual recovery method . . . . 50
In-band automated boot recovery method

. . 51

Out-of-band automated boot recovery
method . . . . . . . . . . . . . . . . 52

Automated boot recovery (ABR) .  .  .  .  .  .  .  .  52
Nx boot failure .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  52
Accessing the IMM .  .  .  .  .  .  .  .  .  .  .  .  .  53

Potential conflicts with the LAN over USB
interface .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  53
Resolving conflicts with the IMM LAN over
USB interface .  .  .  .  .  .  .  .  .  .  .  .  .  .  54
Configuring the LAN over USB interface
manually .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  54

Chapter 3. Parts listing . . . . . . . . 57

Parts listing - BladeCenter HX5 . . . . . . . . . 57
Parts listing - IBM MAX5 . . . . . . . . . . . 62

Chapter 4. Removing and replacing
blade server components . . . . . . . 65

Installation guidelines . . . . . . . . . . . . 65

System reliability guidelines .  .  .  .  .  .  .  .  65
Handling static-sensitive devices .  .  .  .  .  .  66
Returning a device or component .  .  .  .  .  .  66

Removing the blade server from the BladeCenter
chassis .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  66
Installing a blade server in a BladeCenter
chassis .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  67
Disassembling a scalable blade complex .  .  .  .  .  68
Assembling a scalable blade complex .  .  .  .  .  .  70
Removing and replacing Tier 1 customer
replaceable units (CRUs) .  .  .  .  .  .  .  .  .  .  .  71

Removing the blade server cover .  .  .  .  .  .  71
Installing the blade server cover.  .  .  .  .  .  .  73
Removing an expansion unit .  .  .  .  .  .  .  .  74
Installing an expansion unit .  .  .  .  .  .  .  .  75
Removing the battery .  .  .  .  .  .  .  .  .  .  .  76
Installing the battery .  .  .  .  .  .  .  .  .  .  .  77

Removing and replacing Tier 2 CRUs . . . . . . 78

Removing the scalability tray .  .  .  .  .  .  .  .  78
Installing the scalability tray .  .  .  .  .  .  .  .  80
Removing the 1-node speed burst card.  .  .  .  81
Installing the 1-node speed burst card .  .  .  .  82
Removing the 2-node scalability card .  .  .  .  83
Installing the 2-node Scalability card .  .  .  .  .  85
Removing an IBM MAX5 expansion blade .  .  .  87
Installing an IBM MAX5 expansion blade .  .  .  88
Removing the IBM MAX5 1-node Scalability
card

. . . . . . . . . . . . . . . . . 92

Installing the IBM MAX5 1-node Scalability
card

. . . . . . . . . . . . . . . . . 94

Содержание BladeCenter HX5 1909


























































































































































































































































































































Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды

Lenovo BladeCenter HX5 1909, Руководство по диагностике и обслуживанию

Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды