Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 108

Страница: 108 / 313

a. Lay the IBM MAX5 expansion blade on a flat, static-protective surface, cover side down.

b. Use a screwdriver to remove both heat sink access plates.

Step 8. Touch the static-protective package that contains the IBM MAX5 to any

unpainted

metal surface on

the BladeCenter chassis or any

unpainted

metal surface on any other grounded rack component;

then, remove the optional expansion unit from the package.

Step 9. Orient the IBM MAX5 as shown in the illustration.

Step 10. Lower the IBM MAX5 so that the slots at the rear slide down onto the cover pins at the rear of the

blade server; then, pivot the IBM MAX5 down onto the blade server.

Step 11. Press the IBM MAX5 firmly into the closed position until it clicks into place.

Step 12. Install the IBM MAX5 1-node scalability card (see “Installing the IBM MAX5 1-node Scalability card”

on page 94 for instructions).

Step 13. If you are replacing a defective IBM MAX5 expansion blade, transfer the memory DIMMs from the

defective expansion blade to the new expansion blade (see “Removing a DIMM - IBM MAX5
expansion blade” on page 107 and “Installing a DIMM - IBM MAX5” on page 108).

Step 14. Install the blade server or scalable blade complex into the BladeCenter chassis (see “Installing a

blade server in a BladeCenter chassis” on page 67 for instructions).

Removing the IBM MAX5 1-node Scalability card

Use this information to remove the IBM MAX5 1-node scalability card from a blade server.

To remove the IBM MAX5 1-node scalability card, complete the following steps.

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 65.

Step 2. If the blade server or scalable blade complex is installed in a BladeCenter chassis, remove it. See

“Removing the blade server from the BladeCenter chassis” on page 66 for instructions.

Step 3. Remove the cover for the expansion blade (see “Removing the blade server cover” on page 71 for

instructions).

Step 4. Stand the blade server and expansion blade upright on a clean, flat work surface, with the

scalability connector on the blade servers facing up.

Step 5. Open the lower handles (rotate the lower handles down) to allow the blade server and expansion

blade to sit flat on the work surface.

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Содержание BladeCenter HX5 1909


























































































































































































































































































































Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды

Lenovo BladeCenter HX5 1909, Руководство по диагностике и обслуживанию

Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды