Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 313

background image

Attention:

• To maintain proper system cooling, do not operate the BladeCenter chassis without a blade server or filler

module installed in each blade server bay.

• When you remove the blade server, note the blade server bay number. Reinstalling a blade server into a

different blade server bay from the one it was removed from can have unintended consequences. Some
configuration information and update options are established according to blade server bay number. If
you reinstall the blade server into a different bay, you might have to reconfigure the blade server.

To remove a BladeCenter HX5 blade server or scalable blade complex, complete the following steps:

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 65.

Step 2. If the blade server is operating, shut down the operating system.

Step 3. Press the power button to turn off the blade server (see “Turning off the blade server” on page 12

for more information).

Note:

If the blade server is part of a scalable blade complex operating in single partition mode,

pressing the power button on one blade server causes both blade servers to shut down.

Step 4. Open the two release handles as shown in the illustration. The blade server moves out of the blade

server bay approximately 0.6 cm (0.25 inch).

Step 5. Pull the blade server out of the bay.

Step 6. Install either a blade filler or another blade server in the blade server bay within 1 minute.

Installing a blade server in a BladeCenter chassis

Use these instructions to install a BladeCenter HX5 blade server in a BladeCenter chassis.

The following illustration shows how to install a BladeCenter HX5 blade server into a BladeCenter chassis.
See the documentation for your BladeCenter chassis for additional information.

Statement 21

CAUTION:

.

Removing and replacing blade server components

67

«
...
81
82
83
84
85
...
»

Содержание BladeCenter HX5 1909


























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeCenter HX5 1909

Бренд: Aastra Страницы: 502

Бренд: Sun Microsystems Страницы: 90

AssuredSAN 4004 Series

Бренд: Dot Hill Страницы: 59

EDIMAX FAST ETHERNET MFP SERVER VERSION: 2.0

Бренд: Edimax Страницы: 118

InterServe 600 Series

Бренд: Intergraph Страницы: 104

4-Port USB 2.0 Device Server over IP...

Бренд: Quatech Страницы: 2

Netra SPARC T3-1BA

Бренд: Sun Oracle Страницы: 62

Бренд: Sun Oracle Страницы: 182

Бренд: Sun Oracle Страницы: 222

Бренд: Sun Microsystems Страницы: 114

Бренд: Sun Microsystems Страницы: 192

Бренд: Sun Microsystems Страницы: 270

Бренд: hopf Elektronik GmbH Страницы: 178

Бренд: EVS Страницы: 126

Бренд: XtendLan Страницы: 50

Бренд: Intel Страницы: 138

Бренд: easyRAID Страницы: 32

Бренд: Russound Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды