Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 227 | Manualshive

Страница: 227 / 313

background image

• Follow the suggested actions in the order in which they are listed in the Action column until the problem is

solved.

• See “

Parts listing - BladeCenter HX5

” on page 57 to determine which components are CRUs and which

components are FRUs.

• If an action step is preceded by “(Trained service technician only),” that step must be performed only by a

trained service technician.

Lit light path
diagnostics LED

Description

Action

3) Enable the DIMM connector for the DIMM that was replaced.

After installing a DIMM as a result of a DIMM failure, you might need to re-
enable the DIMM connector (slot) for the DIMM that you replaced. To
determine whether you need to re-enable the DIMM:

1. Verify that the amount of memory installed in the IBM MAX5 is the

expected amount of memory. You can verify the amount of memory that
is installed through the operating system, by watching the monitor as the
blade server starts up, or through the advanced management module
web interface.For more information about the advanced management
module web interface, see the http://www.ibm.com/systems/ support/
supportsite.wss/docdisplay? brandind=5000008&lndocid=MIGR-
5073887.

2. Run the Setup Utility to re-enable the DIMMs (see “Using the Setup

utility” on page 20 for more information).

IBM Dynamic System Analysis

IBM Dynamic System Analysis (DSA) collects and analyzes system information to aid in diagnosing server
problems.

DSA collects the following information about the server:

• Drive health information

• Event logs for ServeRAID controllers and service processors

• Hardware inventory, include PCI and USB information

• Installed applications and hot fixes

• Kernel modules

• Light path diagnostics status

• Network interfaces and settings

• Performance data and details about processes that are running

• RAID and controller configuration

• Service processor (integrated management module) status and configuration

• System configuration

• Vital product data and firmware information

If you cannot find a problem by using DSA, see “Solving undetermined problems” on page 274.

Note:

DSA Preboot might appear to be unresponsive when you start the program. This is normal operation

while the program loads.

211

«
...
225
226
227
228
229
...
»

Содержание BladeCenter HX5 1909


























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeCenter HX5 1909

Бренд: IBM Страницы: 198

Бренд: Zenith Страницы: 218

Бренд: Axel Страницы: 28

Бренд: Cable-Tronix Страницы: 33

Anybus Communicator ABC4018

Бренд: HMS Networks Страницы: 64

Бренд: Belkin Страницы: 8

Бренд: Nortel Страницы: 144

DIGI CONNECT ES

Бренд: Digi Страницы: 23

ProLiant DL100 G2 DPSS

Бренд: HP Страницы: 155

NetStorage 6000

Бренд: HP Страницы: 192

ProLiant DL100 G2 DPSS

Бренд: HP Страницы: 44

Бренд: Planet Страницы: 72

Бренд: Certon Страницы: 29

Smartstor NS4600

Бренд: Promise Technology Страницы: 370

Бренд: Solid Страницы: 102

Бренд: Neat Страницы: 124

Бренд: Inspur Страницы: 37

Бренд: 7th Sense Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды