Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 144

Страница: 144 / 313

1. Using a screwdriver or a coin, turn each of the screws toward the middle of the blade server

until they are in the unlocked position.

2. While you lift the back of the access panel, slide the panel away from the bezel.

• Complete the following steps to remove the operator control panel access panel on a

BladeCenter HX5 blade server that does have tall heat sinks:

1. Using a screwdriver, remove each of the screws on the right access panel.

2. Lift the access panel away from the blade server.

Step 9. Locate the control-panel connector on the blade server (see “Blade server connectors -

BladeCenter HX5” on page 12).

Step 10. Touch the static-protective package that contains the control panel to any

unpainted

metal surface

on the BladeCenter unit or any

unpainted

metal surface on any other grounded rack component in

128

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Содержание BladeCenter HX5 1909


























































































































































































































































































































Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды

Lenovo BladeCenter HX5 1909, Руководство по диагностике и обслуживанию

Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды