Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 179 | Manualshive

Страница: 179 / 313

background image

The following table lists IMM error messages that are displayed in the advanced management module event
log and suggested actions to correct the detected problems. These events, in a slightly different format, are
also displayed in the IMM event log.

Note:

An updated list of IMM error messages and corrective actions are available on the IBM website at

http://www.ibm.com/systems/support/supportsite.wss/docdisplay?lndocid=MIGR-5079339&brandind=
5000008.

• Follow the suggested actions in the order in which they are listed in the Action column until the problem is

solved.

• See “

Parts listing - BladeCenter HX5

” on page 57 to determine which components are CRUs and which

components are FRUs.

• If an action step is preceded by “(Trained service technician only),” that step must be performed only by a

trained service technician.

Type

Error Message

Action

Error Code: 0x80010200

Note:

Multiple events can be displayed for this error code. Be sure to read the message text to determine the

appropriate recovery actions.

Error

System board (Planar 12V) voltage
under critical threshold. Reading:

X

,

Threshold:

Y

1. If the under voltage problem is occurring on all blade

servers, look for other events in the log related to power
and resolve those events (see “Event logs” on page 147).

2. View the event log provided by the advanced

management module for your BladeCenter chassis and
resolve any power related errors that might be displayed.

3. If other modules or blade servers are logging the same

issue, check the power supply for the BladeCenter
chassis.

4. (Trained service technician only) Replace the system-

board assembly (see “Removing the system-board
assembly - BladeCenter HX5” on page 140 and “Installing
the system-board assembly - BladeCenter HX5” on page
142).

Error

System board (Planar 5V) voltage
under critical threshold. Reading:

X

,

Threshold:

Y

1. Remove all expansion cards from the blade server (see

“Removing an I/O expansion card” on page 119).

2. Remove all storage drives from the blade server (see

“Removing a solid state drive” on page 101).

3. (Trained service technician only) Replace the system-

board assembly (see “Removing the system-board
assembly - BladeCenter HX5” on page 140 and “Installing
the system-board assembly - BladeCenter HX5” on page
142).

Error

System board (Planar 3.3V) voltage
under critical threshold. Reading:

X

,

Threshold:

Y

1. Remove all expansion cards from the blade server (see

“Removing an I/O expansion card” on page 119).

2. Remove all storage drives from the blade server (see

“Removing a solid state drive” on page 101).

3. (Trained service technician only) Replace the system-

board assembly (see “Removing the system-board
assembly - BladeCenter HX5” on page 140 and “Installing
the system-board assembly - BladeCenter HX5” on page
142).

163

«
...
177
178
179
180
181
...
»

Содержание BladeCenter HX5 1909


























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeCenter HX5 1909

Бренд: Panasonic Страницы: 31

AMX Vision2 V2-MASTER-1210

Бренд: Harman Страницы: 2

Бренд: BELINEA Страницы: 53

SUPERSERVER 5017C-MF

Бренд: Supero Страницы: 96

Бренд: Vxl Страницы: 19

Бренд: DNP Страницы: 2

Бренд: ASROCK Страницы: 40

Бренд: Lenovo Страницы: 186

42U 1200 mm Deep Dynamic Rack

Бренд: Lenovo Страницы: 42

Бренд: Lenovo Страницы: 32

30131AU - IdeaCentre D400 - 3013

Бренд: Lenovo Страницы: 65

Бренд: Lenovo Страницы: 176

Бренд: Lenovo Страницы: 90

Бренд: Lenovo Страницы: 141

Бренд: Lenovo Страницы: 96

Бренд: Lenovo Страницы: 154

Бренд: Lenovo Страницы: 4

Express5800/E120d-1

Бренд: NEC Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды