Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 135

Страница: 135 / 313

Step 14. If the blade server is part of a scalable blade complex, assemble the scalable blade complex (see

“Assembling a scalable blade complex” on page 70 for instructions).

Step 15. Install the IBM MAX5 expansion blade if you removed one (see “Installing an IBM MAX5 expansion

blade” on page 88 for instructions).

Step 16. Install the optional expansion unit, if you removed one from the blade server (see “Installing an

expansion unit” on page 97 for instructions).

Step 17. Install the cover onto the blade server (see “Installing the blade server cover” on page 73 for

instructions).

Step 18. Install the blade server or scalable blade complex into the BladeCenter chassis (see “Installing a

blade server in a BladeCenter chassis” on page 67 for instructions).

Removing an I/O expansion card

The following sections describe how to remove the following expansion cards:

• CFFh

• CIOv

For information about removing the SSD expansion card, see “Removing an SSD expansion card” on page
98.

Removing a CFFh expansion card

Use these instructions to remove a CFFh expansion card from the blade server.

To remove a CFFh expansion card, complete the following steps:

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 65.

Step 2. If the blade server or scalable blade complex is installed in a BladeCenter chassis, remove it. See

“Removing the blade server from the BladeCenter chassis” on page 66 for instructions.

Step 3. Carefully lay the blade server on a flat, static-protective surface.

Step 4. If an optional expansion unit is installed, remove the expansion unit (see “Removing an expansion

unit” on page 96 for instructions).

Note:

Optional expansion units are not supported when a IBM MAX5 expansion blade is installed.

Step 5. If you are removing the CFFh card from a blade server that is the bottom blade server in a scalable

blade complex, disassemble the blade complex (see “Disassembling a scalable blade complex” on
page 68 for instructions).

Step 6. Open the blade server cover (see “Removing the blade server cover” on page 71 for instructions).

Step 7. If an IBM MAX5 expansion blade is installed, remove it (see “Removing an IBM MAX5 expansion

blade” on page 87 for instructions).

Step 8. Locate the CFFh expansion card. The CFFh card is installed in the blade expansion connector (see

“Blade server connectors - BladeCenter HX5” on page 12).

Step 9. Lift the release lever on the CFFh expansion card.

Step 10. Use your fingers to hold the edge of the CFFh expansion card where it connects to the blade

expansion connector; then, lift the card.

Chapter 4

Removing and replacing blade server components

119

Содержание BladeCenter HX5 1909


























































































































































































































































































































Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды

Lenovo BladeCenter HX5 1909, Руководство по диагностике и обслуживанию

Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды