Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 114

Страница: 114 / 313

Blade server
cover release

Cover
Pins

To install and close the blade server cover, complete the following steps:

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 65.

Step 2. Carefully lay the blade server on a flat, static-protective surface, orienting the blade server with the

bezel pointing toward you.

Step 3. Locate the blade expansion connector and remove the cover if one is installed (see “Blade server

connectors - BladeCenter HX5” on page 12).

Step 4. Touch the static-protective package that contains the optional expansion unit to any

unpainted

metal surface on the BladeCenter unit or any

unpainted

metal surface on any other grounded rack

component; then, remove the optional expansion unit from the package.

Step 5. Orient the optional expansion unit as shown in the illustration.

Step 6. Lower the expansion unit so that the slots at the rear slide down onto the cover pins at the rear of

the blade server; then, pivot the expansion unit down onto the blade server.

Step 7. If the expansion unit has a cover already installed, remove it (see “Removing the blade server

cover” on page 71).

Step 8. Install the blade cover from the BladeCenter HX5 (see “Installing the blade server cover” on page

73).

Important:

The BladeCenter HX5 blade cover contains the system-service label on the bottom of

the cover.

Step 9. Install the blade server or scalable blade complex into the BladeCenter chassis (see “Installing a

blade server in a BladeCenter chassis” on page 67 for instructions).

Removing an SSD expansion card

Use this information to remove an SSD expansion card.

To remove an SSD expansion card, complete the following steps:

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 65.

Step 2. If the blade server or scalable blade complex is installed in a BladeCenter chassis, remove it. See

“Removing the blade server from the BladeCenter chassis” on page 66 for instructions.

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Содержание BladeCenter HX5 1909


























































































































































































































































































































Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды

Lenovo BladeCenter HX5 1909, Руководство по диагностике и обслуживанию

Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды