Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 313

background image

Turning off the blade server

When you turn off the blade server, it is still connected to power through the BladeCenter chassis. The blade
server can respond to requests from the service processor, such as a remote request to turn on the blade
server. To remove all power from the blade server, you must remove it from the BladeCenter chassis.

Before you turn off the blade server, shut down the operating system. See the operating-system
documentation for information about shutting down the operating system.

The blade server can be turned off in any of the following ways:

• You can press the power button on the blade server (see “Blade server controls and LEDs” on page 7).

Pressing the button starts an orderly shutdown of the operating system, if this feature is supported by the
operating system.

• If the operating system stops functioning, you can press and hold the power button for more than 4

seconds to turn off the blade server.

Attention:

Pressing the button for 4 seconds forces the operating system to shut down immediately. Data

loss is possible.

• You can turn off the blade server through the advanced management module web interface. For more

information about the advanced management module web interface, see the

IBM BladeCenter Advanced

Management Module: User's Guide

.

System board layouts

Use these system board layouts to locate connectors, LEDs, and switches on the system board of the blade
server.

Blade server connectors - BladeCenter HX5

Use this information to locate blade server system board components and connectors for optional devices.

The following illustration shows the system board components, including connectors for user-installable
optional devices, in the blade server.

12

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

«
...
26
27
28
29
30
...
»

Содержание BladeCenter HX5 1909


























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeCenter HX5 1909

DSN-4100 Series

Бренд: D-Link Страницы: 2

SimpliVity 2600 Gen10

Бренд: HPE Страницы: 37

AirborneDirect ABDG-SE-IN5410

Бренд: Quatech Страницы: 8

Бренд: MSI Страницы: 107

NPort P5250A Series

Бренд: Moxa Technologies Страницы: 2

Бренд: Jung Страницы: 16

Бренд: Axel Страницы: 28

Бренд: Raidon Страницы: 20

Бренд: Supermicro Страницы: 118

Бренд: Xerox Страницы: 2

WSG SoundGrid Server One

Бренд: Waves Страницы: 4

Бренд: Sonnet Страницы: 16

Edgeline EL4000

Бренд: HPE Страницы: 57

ProLiant ML110 Gen10

Бренд: HPE Страницы: 101

ProLiant ML110 Gen10

Бренд: HPE Страницы: 159

Бренд: GRASS VALLEY Страницы: 2

Бренд: XtendLan Страницы: 38

Бренд: Medion Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды