Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 86

Страница: 86 / 313

Blade server
cover release

Secondary
BladeCenter HX5
blade server

Step 7. Install either a 1-node speed burst card (see “Installing the 1-node speed burst card” on page 82)

or a scalability filler on each blade server.To install a scalability filler, complete the following steps:

a. Align the pins on the bottom of the filler with the holes on the scalability connector on the blade

server.

b. Press down firmly so that the filler is flush with the scalability connector on the blade server.

c. Tighten the screw on the scalability filler by hand to ensure that the screw threads start

properly.

d. Using the hex driver that comes with the scalability kit, tighten the nut that attaches the filler to

the blade server.

Step 8. Remove the scalability tray from the topmost blade server (see “Removing the scalability tray” on

page 78 for instructions).

Note:

You only need to remove the scalability tray if you intend to install the blade servers in blade

server bays that are not adjacent or if you intend to install the blade servers in different BladeCenter
chassis.

Step 9. Install a cover on each blade server (see “Installing the blade server cover” on page 73 for

instructions).

Assembling a scalable blade complex

Use this information to assemble a scalable blade complex.

To assemble a scalable blade complex, you need the following parts:

• Two BladeCenter HX5 blade servers

• 2-node scalability kit, which includes the 2-node scalability card, the scalability tray, and the 3/16" hex

driver.

To assemble a scalable blade complex, complete the following steps:

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 65.

Step 2. Remove the covers for both blade servers (see “Removing the blade server cover” on page 71).

Step 3. Install all optional components, such as DIMMs and SSDs in each of the blade servers.

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Содержание BladeCenter HX5 1909


























































































































































































































































































































Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды

Lenovo BladeCenter HX5 1909, Руководство по диагностике и обслуживанию

Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды