Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 232 | Manualshive

Страница: 232 / 313

background image

• See “

Parts listing - BladeCenter HX5

” on page 57 to determine which components are CRUs and which

components are FRUs.

• If an action step is preceded by “(Trained service technician only),” that step must be performed only by a

trained service technician.

Error code

Description

Action

5. If the blade server has stopped responding, turn

off and restart the blade server; then, run the
test again. See “Turning off the blade server” on
page 12 and “Turning on the blade server” on
page 11.

6. (Trained service technician only) If the

component failure remains, see Chapter 4
“Removing and replacing blade server
components” on page 65 to replace the failed
component.

089-901-xxx

Failed the CPU stress test.

1. If the blade server has stopped responding, turn

off and restart the blade server; then, run the
test again. See “Turning off the blade server” on
page 12 and “Turning on the blade server” on
page 11.

2. Make sure that the DSA code is up-to-date,

upgrade if necessary; then, run the test again.
The latest code can be found at http://www.ibm.
com/systems/ support/supportsite.wss/
docdisplay? brandind=5000008&lndocid=
SERV-DSA.

3. Make sure that the system firmware level is up-

to-date, upgrade if necessary; then, run the test
again. The installed firmware level can be found
in the DSA log within the Firmware/VPD section
for this component. The latest level firmware for
this component can be found at http://www.
ibm.com/support/ fixcentral/systemx/
groupView? query.productGroup=ibm%
2FBladeCenter.

4. If the blade server has stopped responding, turn

off and restart the blade server; then, run the
test again.

5. (Trained service technician only) If the

component failure remains, see Chapter 4
“Removing and replacing blade server
components” on page 65 to replace the failed
component.

Memory tests

Use this information to diagnose and resolve memory test errors.

Follow the suggested actions in the order in which they are listed in the Action column until the problem is
solved.

216

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

«
...
230
231
232
233
234
...
»

Содержание BladeCenter HX5 1909


























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeCenter HX5 1909

SuperServer E100-8Q

Бренд: Supermicro Страницы: 48

Flex System x440 Compute Node

Бренд: IBM Страницы: 584

Бренд: Avaya Страницы: 19

INTUITY AUDIX LX

Бренд: Avaya Страницы: 68

Бренд: Supermicro Страницы: 124

Netfinity 4500R

Бренд: IBM Страницы: 60

Бренд: Fujitsu Страницы: 26

Бренд: Fujitsu Страницы: 56

Бренд: Fujitsu Страницы: 36

Бренд: Fujitsu Страницы: 61

Бренд: Fujitsu Страницы: 30

ETERNUS DX Disk

Бренд: Fujitsu Страницы: 85

Бренд: Fujitsu Страницы: 111

BX630 - PRIMERGY - S2 Dual

Бренд: Fujitsu Страницы: 64

Бренд: Fujitsu Страницы: 68

CELVIN NAS QE707

Бренд: Fujitsu Страницы: 95

BX630 - PRIMERGY - S2 Dual

Бренд: Fujitsu Страницы: 90

D3320 PRIMERGY BX2560 M2

Бренд: Fujitsu Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды