Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 191

Страница: 191 / 313

• Follow the suggested actions in the order in which they are listed in the Action column until the problem is

solved.

• See “

Parts listing - BladeCenter HX5

” on page 57 to determine which components are CRUs and which

components are FRUs.

• If an action step is preceded by “(Trained service technician only),” that step must be performed only by a

trained service technician.

Type

Error Message

Action

Error

Processor

, temperature (CPU

OverTemp) non-recoverable [Note:

=1-2]

1. Make sure that the room temperature is within the

operating specifications (see “Features and
specifications” on page 4).

2. Make sure that none of the air vents on the BladeCenter

chassis and on the blade server are blocked.

3. Make sure that all of the fans on the BladeCenter chassis

are running.

4. Make sure that each bay of the BladeCenter chassis

contains either a device or a filler.

5. Make sure that the blade server is not missing any heat

sinks, DIMMs, or heat-sink fillers (see “Parts listing -
BladeCenter HX5” on page 57).

6. (Trained service technician only) Make sure that the

microprocessor heat sink is properly attached to the
microprocessor (see “Installing a microprocessor and heat
sink” on page 134).

Error

System board, interconnect (Pwr
Share Jumper) non-recoverable

1. Reseat the cap on the power sharing connector (see

“Blade server connectors - BladeCenter HX5” on page
12).

2. (Trained service technician only) Replace the system-

board assembly (see “Removing the system-board
assembly - BladeCenter HX5” on page 140 and “Installing
the system-board assembly - BladeCenter HX5” on page
142).

Error Code: 0x80090000

Information

System board, memory
(Performance Mode) disabled/
enabled

This is informational only, no action is required. The
performance mode has been enabled or disabled.

Error Code: 0x800B0100

Chapter 5

Diagnostics

175

Содержание BladeCenter HX5 1909


























































































































































































































































































































Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды

Lenovo BladeCenter HX5 1909, Руководство по диагностике и обслуживанию

Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды