Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 150

Страница: 150 / 313

Installation
tool

Microprocessor

Alignment
holes

Screws

Step 16. If you are instructed to return the microprocessor and heat sink, follow all packaging instructions,

and use any packaging materials for shipping that are supplied to you.

Installing a microprocessor and heat sink

Use this information to install a microprocessor and heat sink in the blade server.

Note:

The optional microprocessors that IBM supports are limited by the capacity and capability of the

server. Any microprocessors that you install must have the same specifications as the microprocessors that
came with the blade server.

The following illustration shows how to install a microprocessor and heat sink in the blade server.

Heat sink

Microprocessor
heat sink filler

Attention:

1. Do not use any tools or sharp objects to lift the locking lever on the microprocessor socket. Doing so

might result in permanent damage to the system board.

2. Do not touch the contacts in the microprocessor socket. Touching these contacts might result in

permanent damage to the system board.

To install a microprocessor and heat sink, complete the following steps:

134

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Содержание BladeCenter HX5 1909


























































































































































































































































































































Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды

Lenovo BladeCenter HX5 1909, Руководство по диагностике и обслуживанию

Результаты поиска

Содержание BladeCenter HX5 1909

Отзывы:

Похожие инструкции для BladeCenter HX5 1909

Бренды по названию

Популярные бренды