Lenovo BladeCenter HX5 1909 Скачать руководство пользователя страница 287 | Manualshive

Страница: 287 / 313

background image

3. Media tray

Step 4. For problems that affect only the CD or DVD drive, make sure that:

a. The CD or DVD is inserted correctly in the drive. If necessary, insert the end of a straightened

paper clip into the manual tray-release opening to eject the CD or DVD. The drive LED flashes
once per second when the CD or DVD is inserted.

b. The CD or DVD is clean and not damaged. (Try another CD or DVD if you have one.)

c. The software program is working properly.

Step 5. For problems that affect one or more of the removable media drives:

a. Reseat the following components:

1. Removable-media drive cable (if applicable)

2. Removable-media drive

3. Media tray cable (if applicable)

4. Media tray

b. Replace the following components one at a time, in the order shown, restarting the blade

server each time:

1. Removable-media drive cable (if applicable)

2. Media tray cable (if applicable)

3. Removable-media drive

4. Media tray

Step 6. Check for correct advanced management module operation (see the documentation for your

BladeCenter chassis).

Note:

Some BladeCenter chassis types have several management-module components that might

have to be tested or replaced (see the

Installation Guide

for your advanced management module

for more information).

Step 7. Replace the advanced management module (see the documentation for your BladeCenter chassis).

If these steps do not solve the problem, it is likely a problem with the blade server. See “Removable-media
drive problems” on page 267 or “Universal Serial Bus (USB) port problems” on page 273.

Network connection problems

Use this information to diagnose and solve network connection issues with the blade server.

To check for network connection problems, complete the following steps until the problem is solved:

Step 1. Make sure that:

•  The network cables are securely connected to the I/O module.
•  Power configuration of the BladeCenter chassis supports the I/O-module configuration.
•  Installation of the I/O-module type is supported by the BladeCenter chassis and blade server

hardware.

• The I/O modules for the network interface that is being used are installed in the correct

BladeCenter I/O-module bays and are configured and operating correctly.

• The settings in the I/O module are correct for the blade server (settings in the I/O module are

specific to each blade server).

Step 2. Check for correct I/O-module operation; troubleshoot and replace the I/O module as indicated in

the documentation for the I/O module.

Step 3. Check for correct management-module operation (see the documentation for your BladeCenter

chassis).

271

«
...
285
286
287
288
289
...
»

Содержание BladeCenter HX5 1909


























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeCenter HX5 1909

BladeCenter HS23

Бренд: IBM Страницы: 28

eServer 200 xSeries

Бренд: IBM Страницы: 128

eServer 232 xSeries

Бренд: IBM Страницы: 174

UniServer BT716F

Бренд: H3C Страницы: 44

Бренд: B&B Страницы: 55

Бренд: Shenzhen JingFeng Страницы: 11

Portbase PB-3010

Бренд: SystemBase Страницы: 45

LUXOMAT net ViSTATION

Бренд: B.E.G. Страницы: 4

Бренд: Lucent Technologies Страницы: 85

Бренд: Digital Equipment Страницы: 73

Бренд: IBM Страницы: 51

Бренд: BELINEA Страницы: 53

Бренд: BlueBroadcaster Страницы: 21

ReadyNAS 3220 Series

Бренд: NETGEAR Страницы: 4

Бренд: IBM Страницы: 100

Бренд: MRV Communications Страницы: 65

Бренд: Epson Страницы: 28

EpsonNet 802.11b

Бренд: Epson Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды